Aeotec AEOEZWA024 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 37

background image

24/11/2022, 15:52

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

https://manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZWA024&cert=ZC12-20120147

9/37

communcation missed.

Green

= Great health

Press and hold [15, 20
seconds)

Blinking

Red

Release here to cancel Factory Reset.

Press and hold [20+ seconds)

Blue

fade in/out for

2 seconds.

Factory Reset.

Communication to a Sleeping device (Wakeup)

This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to
communicate with the device, a static controller

C

is needed in the network. This controller will maintain a mailbox for the battery operated devices and store

commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is
signiﬁcantly decreased.

This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notiﬁcation. The controller can then empty the mailbox.
Therefore, the device needs to be conﬁgured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this
controller will usually perform all necessary conﬁgurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the
device. To wakeup the device please perform the following action:

Waking up MultiSensor 7.

In order to conﬁgure Multisensor 7, you must either (1) wake up Multisensor 7 using the below button press function, or (2) temporarily put your Multisensor 7 on
USB power.

This section will go over the manual wakeup of this sensor in case you don‘t want to wait for conﬁguration.

Quick Wakeup.

1. Press and hold Multisensor 7 Action button

2. Wait until the LED turns into a

Red

Color (1 - 2 seconds)

3. Release Multisensor 7 Action Button, the LED should turn off right away. Any queued commands in your Z-Wave Controller will be sent over.

«
...
7
8
9
10
11
...
»

Содержание AEOEZWA024






































Отзывы:

Нет отзывов

Похожие инструкции для AEOEZWA024

BAKER HUGHES DPS 5000 Series

Бренд: GE Страницы: 36

Бренд: Oemtools Страницы: 8

Бренд: U.S. General Страницы: 5

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 22

Бренд: Campbell Страницы: 62

Бренд: Campbell Страницы: 26

Бренд: CAMPAGNOLO Страницы: 133

Бренд: Campbell Страницы: 34

Бренд: CAMPARK Страницы: 20

Бренд: R.M. Young Страницы: 4

Бренд: Campbell Страницы: 36

Line FP7000 Housing

Бренд: Fantasea Страницы: 5

Бренд: Fantasea Страницы: 5

Бренд: Fancom Страницы: 49

Бренд: FANATEC Страницы: 2

Бренд: Kathrein Страницы: 7

Бренд: Kathrein Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды