background image

AC Clamp-on Meter Model CM605 

19

 

Limited Warranty

The Model CM 605 is warranted to the owner for a period of one year from the 

date of original purchase against defects in manufacture. This limited warranty 

is given by AEMC

®

, not by the distributor from whom it was purchased. This 

warranty is void if the unit has been tampered with, abused or if the defect is 

related to service not performed by AEMC

®

For full and detailed warranty coverage, go to www.aemc.com. The war-

ranty information is located in our customer service section.
What AEMC

®

 will do:

If  a  malfunction  occurs  within  the  one-year  period,  you  may  return  the 

instrument to us for repair, provided you submit a proof of purchase. AEMC

®

 

will, at its option, repair or replace the faulty material.

Warranty Repairs

What you must do to return an Instrument for Warranty Repair: 

First, request a Customer Service Authorization Number (CSA#) by phone 

or by fax from our Service Department (see address below), then return the 

instrument along with the signed CSA Form. Please write the CSA# on the 

outside of the shipping container. Return the instrument, postage or shipment 

pre-paid to:

 

AEMC

®

 Instruments

 

Service Department 

 

15 Faraday Drive • Dover, NH 03820 USA

 

Tel:  (800) 945-2362  (Ext. 360)

 

 

(603) 749-6434  (Ext. 360)

 

Fax:  (603) 742-2346 or (603) 749-6309

Caution:

 To protect yourself against in-transit loss, we recommend you insure 

your returned material.

NOTE: 

You must obtain a CSA# before returning any instrument.

Содержание CM605

























Отзывы: