background image

 

Page 8

 

 

 

 

 

 

WARRANTY 

12 MONTH LIMITED WARRANTY 

 
Advanced  Engine  Management  Inc.  warrants  to  the  consumer  that  all  AEM  High  Performance  products  will  be  free  from  defects  in  material  and 
workmanship  for  a  period  of  twelve  (12)  months  from  date  of  the  original  purchase.  Products  that  fail  within  this  12-month  warranty  period  will  be 
repaired  or  replaced  at  AEM’s  option,  when  determined  by  AEM  that  the  product  failed  due  to  defects  in  material  or  workmanship.  This  warranty  is 
limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be 
responsible  for  special,  incidental  or  consequential  damages  or  cost  incurred  due  to  the  failure  of  this  product.    Warranty  claims  to  AEM  must  be 
transportation  prepaid  and  accompanied  with  dated  proof  of  purchase.  This  warranty  applies  only  to  the  original  purchaser  of  product  and  is  non-
transferable.  All  implied  warranties  shall  be  limited  in  duration  to  the  said  12  month  warranty  period.  Improper  use  or  installation,  accident,  abuse, 
unauthorized  repairs  or  alterations  voids this  warranty.  AEM  disclaims  any  liability for  consequential damages  due  to  breach  of  any  written  or  implied 
warranty  on  all  products  manufactured  by  AEM.  Warranty  returns  will  only  be  accepted  by  AEM  when  accompanied  by  a  valid  Return  Goods 
Authorization (RGA) number.  Product must be received by AEM within 30 days of the date the RGA is issued. 
 
Please  note  that  before  AEM  can  issue  an  RGA  for  any  product,  it  is  first  necessary  for  the  installer  or  end  user  to  contact  the  AEM  Performance 
Electronics tech line at 1-800-423-0046 to discuss the problem.  Most issues can be resolved over the phone.  Under no circumstances should a system 
be returned or a RGA requested before the above process transpires. 
 

Need additional help?  Contact the AEM Performance Electronics tech department at  
1-800-423-0046 or [email protected], or visit the AEM Performance Electronics forum at 

http://forum.aempower.com/forum/

 

Содержание 30-3431









Отзывы: