UNPLUGGABLE WIRE HARNESS
DO NOT apply power to the alarm control panel while making connections. Tape all the wire
ends of the unused wires.
1 (RED)
:
This terminal provides a cont12V output power at normal condition
of no alarm. The +12V output is switched OFF at alarm condition. The
output is equipped with a 1.5A resettable fuse.
This terminal pr12V output power at alarm condition with the time
period according to the setting of the alarm timer. It is suitable for energizing
electronic siren or alarm bell. The output is equipped with a 1.5A resettable fuse.
This terminal is prepared for connecting the arm-disarm remote keyswitches
(eg. Model: RKS-2M) or the wireless remote controller (e.g. Model: RPS-302M).
It accepts Normally Open (N.O.) momentary switches and is +12V
triggered. Maximum 3 remote switches can be connected in parallel.
This terminal provides an unsw12V output power refering to the
common ground. It gives output power all the time no matter the system is
armed or disarmed. Suitable for those devices require uninterrupted power
supply. Such as smoke detectors, motion sensors, control keypads etc. This
terminal is equipped with a 750mA resettable fuse.
2 (BLACK)
:
3 (GREY)
:
4 (GREEN)
:
Common Ground ( ).
-
5 (LIGHT BLUE) :
UTILIZE THE REMOTE KEY SWITCH FOR SYSTEM ARM-DISARM CONTROLS
ARM THE SYSTEM
KEY SWITCH
CONTACT
1st Touch
2nd Touch
1st Touch
2nd Touch
DISARM THE SYSTEM
STATUS
!
!
!
!
!
Away mode arming
Home mode arming
System disarmed
Alarm memory is
cleared
System keeps in
disarmed mode
RESULTS
!
!
!
!
!
!
!
!
!
!
Exit delay starts
Exit beep sounds if it is enabled
System will be armed after exit delay expired
The 2nd touch must be made within the exit delay
period
Exit beep sounds continuously until the end of the exit
delay
System will be armed after exit delay expired
The system is disarmed and reset if there was no
alarm occurred. It is ready for re-arming
The system is disarmed but with alarm memory if
there was alarm occurred, 2nd touch is required
The alarm memory LEDs are off
The system is ready for re-arming
(The zone LEDs on
the control console)
TERMINAL DEFINITIONS AND DESCRIPTIONS
10
HA-266
DELETE A USER CODE
CHANGE A TELEPHONE NUMBER IN AUTO-DIALER
8 user code locations are available in the system but putting user codes into all of them is
optional. A user code in a location can be changed or deleted at anytime you like.
MASTER CODE
The
light comes ON.
USER CODE LOCATION
#
The user code in that location is deleted.
If the request is rejected, 5 beeps will be generated. Try again.
System is back to operation mode.
The telephone numbers in both communicator and auto dialer can be changed or deleted if
required. The telephone number entry for communicator is usually handled by the installer or by
the technician of the monitor station. Details are described in the INSTALLATION SECTION,
programming locations 50-51.
The telephone numbers that you put in the auto dialer are usually the numbers of your friends,
relatives, your home/office phone, and even your portable phone or pager, you may change the
numbers from time to time. The 4 telephone numbers are stored at locations 60-63.
MASTER CODE
The
light comes ON.
TELEPHONE LOCATION
1
TELEPHONE NUMBER
#
1) Enter your [MASTER CODE] and validate by [ ] [ ]
2) Enter the user code location [11-18] you wish to deleted its user code and validate by [#]
3) Exit the programming mode by pushing [ ] [ ]
1) Enter your [MASTE CODE] and validate by [ ] [ ]
2) Enter the telephone location [60-63] you wish to change its telephone number, key in
the message form [0 or 1] required, enter the new [TELEPHONE NUMBER] and validate
by [#].
NEW
!
!
!
!
!
PROGRAM
PROGRAM
CHANGE AND DELETE
67
HA-266
