7
SET THE SYSTEM TO SINGLE USER MODE
SET THE SYSTEM TO MULTI-USER MODE
REFRESH THE SYSTEM
You are required to decide the keypad for Single User or Multi-User Mode in operation. The system can be set for
with the command code "
" and stay in that mode unless the system is refreshed for other
mode.
he system can be set for
with the command code "
" and stay in that mode unless the
system is refreshed for other mode.
A system was set to
It is possible to change it to
; or vice versa. Just refresh
the system with the above operation command codes.
A refreshed keypad will reset itself as a fresh unit with the Default Values.
Make sure all the
and
are set to
after the system is refreshed for Single
User Mode operation. Otherwise, code entry will not be successful.
It is necessary to change the Master Code to 4 digits first (if it was more than 4 digits in Multi Users Mode)
before refreshing from Multi User Mode to Single User Mode.
The system takes approximate 2 to 3 seconds to refresh itself for new operation mode after the refresh code is
entered. DO NOT enter any code during the system is being refreshed until the 2 confirmation beeps are heard.
Single User Mode
8900
MASTER CODE
Single User Mode
Multi User Mode
8901
MASTER CODE
Multi-User Mode
Single User Mode.
Multi-User Mode
All the programmed data that saved
previously are cleared except the Master Code.
IMPORTANT NOTES:
1)
User Codes
Master Code
4 Digits
2)
3)
(wait 2-3 seconds until the confirmation beeps are heard)
(wait 2-3 seconds until the confirmation beeps are heard)
T
-- CHANGE OF OPERATION MODE
q
* 8900 # --------
* 8901 #
PROGRAM AND USE THE KEYPAD
-- OPERATION
Once the operation mode is selected - Single User or Multi Users, all the three outputs will operate with that mode.
-- Set the following data into the system:
a) Single User Mode Operation
b) Change the factory-set Master Code 0000 to a Personal Master Code 3289
c) Set User Code 1 in 8321
d) Set User Code 2 in 6854
e) Set User Code 3 in 9270
f ) Set Output 1 in Momentary Mode, 1 second
g) Set Output 2 in Start / Stop Mode without accelerated code
h) Set Output 3 in Start / Stop Mode with accelerated code
i ) Set the keypad to lock itself during 15 minutes after 10 successive false codes
j ) Set the keypad with door Forced-Open-Alarm enabled
k ) Set the allowable time for door left open for 60 seconds before triggering of the door Open-Too-Long
alarm
A) SINGLE USER MODE OPERATION
-- An Example
1) Re uirement
8
2) Programming
NOTE:
a)
Press
is not
required.
b)
Duress Code
User Code 1 of Two units
For example:
NOTE:
-- Set the above requirement into the keypad:
---------------- Enter to programming mode with the factory-set Master Code
a) **Enter the Single User Mode Command Code "8900" may not be necessary if the keypad was
already in Single User Mode.
b) In case of wrong entry during programming, cancel it with
key, or, wait 10 seconds, then re-
enter.
To command the output 1, 2 & 3, enter the corresponding codes into the keypad.
The
does not need to program. The keypad determines it automatically by increasing the
first digit of the
.
The User Code 1 is "1234", then the Duress Code is "3234"; or the User Code 1 is
"8321", then the Duress Code is "0321".
To command the Duress Function, enter the Duress Code.
i) The Duress Code has double actions. It activates the Duress Output and at the same time activates
the Output 1 as like the User Code 1. The Duress Code can always activates or deactivates (in Start
/ Stop mode) Output 1, but cannot deactivate (reset) the Duress Output. ONLY the User Code 1 can
deactivate (reset) the Duress Output.
ii) All alarms will be stopped, including the door forced-open-alarm and the door open-too-long alarm,
when Duress function is in operation.
0000 *
8900 #
0 3289 #
1 8321 #
2 6854 #
3 9270 #
40 1 #
51 #
62 #
72 10 #
81 #
9 60 #
*
8321
6854
9270
0321
---------------- System has been set for Single User Mode**
------------ 3289 has been saved as the new Personal Master Code
------------ 8321 has been saved as User Code 1, with Duress
Alarm OFF Code functions
------------ 6854 has been saved as User Code 2
------------ 9270 has been saved as User Code 3
---------------- Output 1 has been set in Momentary Mode, 1 second
-------------------- Output 2 has been set in Start / Stop Mode without accelerated code
-------------------- Output 3 has been set in Start / Stop Mode with accelerated code
-------------- The keypad has been set to lock during 15 minutes after 10 successive false
codes
-------------------- The keypad has been set with door Forced-Open-Alarm enabled
---------------- The keypad has been set with 60 seconds allowable time for door left open
--------------------------- Keypad exits programming mode. All the data above are saved and ready for use
-- Taking the data programmed above as reference
----------------- Output 1 activates for 1 second
----------------- Output 2 starts (or stops)
----------------- Output 3 starts (or stops)
----------------- Duress output activates (output switches to ground) & Output 1 activates for 1
second
&
3) Operate The Keypad
#
#
