manualshive.com logo in svg

Aegis M-PA UHF, Руководство по обслуживанию

Поделиться
Скачать
Aegis M-PA UHF Скачать руководство пользователя страница 7

LBI-33057

7

UDC flex/UDC/Monitor Button/HT Switch Assembly
Removal

If UDC Flex/UDC/Monitor Button/PTT Switch as-

sembly removal is necessary, first unsolder the micro-
phone. With a spanner wrench, remove the UDC  secur-
ing screw (the UDC ground pin). Remove the  insulator
(foam or plastic type) on the  inside side-rail of the case.
Lift the UDC/Monitor Button/PTT Switch assembly from
the side of the case and slide the flex through the slot.

Earlier Front Cover Assembly Keypad Flex Removal

To remove the Keypad Flex, first remove the  UDC

Flex/UDC/Monitor Button/PTT Switch assembly as pre-
viously  stated. Next remove the knobs using the  hex
driver. Unscrew the two (2) screws securing the top panel
and lift and remove the panel. Lift the Emergency Button
Board by carefully unplugging J6 from P6. With a span-
ner wrench, remove the  nuts securing the volume and
channel controls and carefully slide the  controls inside
the radio. Unscrew the two (2)  screws (G and GG)  and
remove the J10/P10 Zebra strip securing plate (HH). See
Figure 5. The Keypad Flex is now free for removal.

Later Front Cover Assembly Keypad flex Removal

To remove the Keypad Flex, first remove the  UDC

Flex/UDC/Monitor Button/PTT Switch assembly as pre-
viously stated. Next remove the screw securing the emer-
gency switch support (G) then remove the  support. Re-
move the knobs using the  hex driver. With a spanner
wrench, remove the nuts securing the volume and  chan-
nel controls and carefully slide the  controls inside the
radio.  Unscrew  the  two  (2)  screws that  secure the
J10/P10 connection at the bottom of the LCD  Board.
Remove the screws, the  plate and  the rubber pad. The
Keypad Flex is now free for removal.

Speaker Flex Removal

In order to replace the Speaker Flex, it must be un-

soldered from the speaker and the Battery Plate.

LCD BOARD ACCESS

To remove the LCD Board, partial removal (actually

repositioning of the top areas) of the Keypad Flex is re-
quired. UDC  Flex/UDC/Monitor Button/PTT Switch as-
sembly removal is not necessary.

After the top areas of the Keypad Flex have been

freed as previously outlined, the LCD  Board can  be re-
moved. At this point is the disassembly process an earlier
Front Cover Assembly has two (2) screws on the left side
as viewed from the back (J and JJ) and  a later assembly
has a single screw in the  upper left-hand side (J). See
Figure 5.

Figure 5 - Keypad Flex and LCD Board Access

Содержание M-PA UHF































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды