background image

7

7

STEP 3: ATTACHING THE HANDLE

See figure 5.

 

 CAUTIoN

Be careful to avoid pinching your fingers or hands when installing 

the handle onto the frame.

Attach the handle on the end of the stand assembly opposite the 

wheels.

 

Insert handle into stand assembly as shown.

 

Align the holes in the handle with the holes in the stand assembly.

 

Insert the bolt through the holes in the handle and the stand 

assembly.

 

Place acorn nut onto bolt and tighten.

 

Repeat on other side.

STEP 4: INSTALLING THE FrAME SUPPorT

See figure 6.

Install the frame support on the stand assembly on the same end as 

the wheels.

 

Insert frame support into stand assembly as shown.

 

Align the holes in the frame support with the holes in the stand 

assembly.

 

Place feet onto the stand assembly with logo facing the frame. 

Align the holes in the feet with the holes in the frame and frame 

support.

 

Insert foot bolts (M8 x 55mm) through the holes in the feet so the 

bolts extend up through the frame and frame support.

 

Install wing nuts and tighten.

 

Repeat on other side.

STEP 5: SECUrING THE ToP rAILS To THE CENTrAL brACE

See figure 7.

 

Raise the stand assembly so that it rests on its wheels and frame 

support. This is the vertical closed position.

NoTE:

 Do not place the stand assembly in the vertical closed 

position until the frame support is installed and all previous 

assembly procedures have been followed.

 

Align the holes in the brackets with the holes in the central brace 

as shown.

 

Insert bolts through the holes in the bracket and central brace.

 

Place nuts onto bolts and tighten securely, do not over tighten.

 

 wArNING

To reduce the risk of injury, make sure top rails are secured to the 

central brace. Failure to secure the top rails could cause instability 

during use resulting in possible serious injury.

Fig. 6

1 - Frame support

2 - Foot bolt (M8 x 55mm)  

3 - Feet

4 - Wing nut (M8) 

2

2

3

4

1

3

4

Fig. 5

1 - Handle

2 - Handle bolt (M8 x 45mm)

3 - Acorn nuts

3

2

2

1

Fig. 7

1 - Top rails

2 - Frame bolt (M8 x 55mm) 

3 - Central brace 

4 - Lock nut (M10) 

5 - Bracket

2

5

3

1

2

4

Содержание PSUM1000

















Отзывы: