AEG Oxygen Скачать руководство пользователя страница 7

AEG 

installation manual

7

1) The 90° inlet elbow may be installed only together with the mounting 
bracket and the inlet valve. Anywhere else in the tubing system, 90° 
sweep elbows and 45° elbows should be used. (Fig. A and B)

2) Tubes are cut straight so that the cutting line is not slanted. Use a miter 
saw if possible. Cut edges can be fi nished with a knife (to remove burrs). 

3) For tubing joints, use suitable PVC glue to make the fi ttings secure and 
tight. Apply a thin and even layer of glue only to the end of the tube – not 
to the sleeve. This will prevent the glue from overfl owing to the end face 
of the tubing. Close the glue can carefully immediately after use and make 
sure to have adequate ventilation during installation. Avoid inhaling glue 
vapors. Insert the tube all the way into the sleeve while turning it at the 
same time (Fig. C). 

4) The inlet is made through the fi re wall according to Fig.fi gure E or by 
using a 2” (50mm) diameter fi re cuff (Fig. D). Check the inlet with a fi re 
authority. 

mounting bracket

90° elbow

90°

sweep 

elbow

A

B

Tubing System Installation

Important notes for installation!

correct

incorrect

incorrect

pipe collars are attached 
to the wall

wire mesh

concrete

sand

vacuum pipe   electrical tube

2” (51 mm)

fi re stopping pipe 
collars

E

F

correct

correct

incorrect

D

min. 3/4” (18 mm)

push the pipe completely into the fi tting

C

Begin the main tube installation with the farthest inlet valve and place the 
tubes temporarily at fi rst. Do not glue the joints yet until you have made 
sure that the tubing routing is correct. The glue will dry quickly; therefore, 
the joints have to be fi tted right after applying the glue. 

When measuring the tubes, take into account that the tube goes appro-
ximately 2/3” (18mm) into the sleeve and approximately 7/8” (20mm) into 
the extension tube. 

The tubing system can also be installed in a fl oor that will be concrete 
casted later on (Fig. F). In such cases, the low-voltage cable must be 
protected by a conduit pipe. The conduit pipe should be attached to the 
vacuum tube or the casting net. For the vacuum tube, the routing channel 
has to be 2” wide (51mm). The ends of the vacuum tubes and the con-
duit pipes should be plugged before concrete casting.

 vacuum pipe

wall

vacuum pipe

min. 7 7/8”

(200 mm)

protects the combustible 
building material

steel protective sleeve
min. 1/ 16” (2 mm)

wall

Installation Examples

Содержание Oxygen












Отзывы: