AEG Oxygen Скачать руководство пользователя страница 5

AEG 

installation manual

5

Inlet Hole

Make a hole in the board material for the inlet valve as shown in the fi gure. 
The size of the rectangular opening should be 2 3/8” x 4 3/4” (60mm x 
110mm). In existing houses where tubes are routed underneath, a hole can 
be drilled for the tube using a guide hole as a template. Glue the 90° inlet 
elbow onto the sleeve of the mounting bracket. Leave a gap of approxi-
mately 5/8” (15cm) for the low-voltage cable to be connected to the inlet 
valve. Then the dust tube is glued into the inlet elbow.

Strip off approximately 1” (2cm to 3cm) of the insulation from the end 
of the low-voltage cable. Roll the end of the cable two turns around the 
screws in the inlet valve and tighten the screws. 

Screw the inlet valve into the mounting bracket and make sure that the 
screw does not extend through the tube. If necessary, use shorter screws. 
In a complete wall structure, the mounting bracket is held in place by a 
hook as shown in the fi gure.

Installation in a Brick or Concrete Wall

When installing the inlet valve, sink the pipes, the inlet elbow, and the 
mounting bracket in the wall so that the highest surface of the mounting 
bracket is approximately 1/4” (5mm) deeper than the fi nal inner surface. 
For the tubing system, make a 3 1/8” x 3 1/8” (80mm x 80mm) channel 
in the brick or concrete wall independent of the fi nal thickness of the wall. 
The tubing installation must be sturdy enough so that tubes and parts 
do not move out of their positions later during the installation work. It is 
recommended to cover the opening of the inlet valve to protect it from cast 
material.

fi nished wall surface

wall mounting 
bracket

3 1/8” (80 mm)

pipe

90° elbow

low voltage 

cable

Thread the low voltage cable through the slot 
in the mounting bracket

mounting 

bracket

    

min. 5/8” (15 cm)

wall

The tube can also be installed block / brick 
wall with the rear side. In this case, the wall 
is made imurasiaa for a picture with the hole.

2 3/8”

(60 mm)

4 3/4”

 (110 mm)

2 3/8” (

60 mm)

4 3/4” (

110 mm)

2 1/4”-2 1/2”

(57–62 mm)

Do not disconnect the mounting screws 
completely. Loosen them enough to fi t 
the low voltage cable around them and 
then tighten.

long screw

short screw

inlet vavle

mounting bracket

low voltage cable

90° elbow

pipe

hook

wall

fi nis

Содержание Oxygen












Отзывы: