AEG AS-M 2 Series Скачать руководство пользователя страница 7

7

AEG STANDARD MODULE INSTALLATION MANUAL

GD202104 V1-21

EN

Ensure to avoid shadowing from module clamps. Please 
refer to figure 4 and figure 6, and paragraph 3.2.4 
„Loading capacity“ for details on the individual product 
series. 

Figure 4: Clamping

3.2.3 Insertion systems

AEG solar modules are compatible with the insertion 
systems of selected manufacturers. For more 
information, and for a compatibility assessment of the 
insertion system you wish to use, contact the AEG 
service team (see Section 6 „Contact“).

3.2.4 Loading capacity

The PV module‘s load resistance is rated as:    
Wind load: 2400 Pa / Snow load:  5400 Pa.  
Please note this could vary according to the different 
mounting systems and configurations.

For standard conditions, low loading capacity applies: 
AEG modules are tested under a maximum positive 
pressure of 2400 Pa, and negative pressure of 2400 Pa. 

For extreme conditions (e.g.: heavy snow), high loading 
capacity applies: AEG modules are tested under a 
maximum positive pressure of 5400 Pa, and negative 
pressure of 2400 Pa.

Please note the indications in the below pictures:

L=module length (module long side)   

W=module width (module short side)  

X, Y=clamp installation point/ 

(arrows) bolting/clamping points

Mounting with bolts

Module series:  

AS-Mxxx2,  

AS-Mxxx9, AS-Pxxx9  

Module series: AS-Mxxx2,  

AS-Mxxx8, AS-Pxxx8,  

AS-Mxxx9, AS-Pxxx9

Load: 

positive 2400Pa 

negative 2400 Pa

Load 

positive 5400 Pa

negative 2400 Pa

Module series:  

AS-M1203 (G1),  AS-M1203 (M6), 

AS-M3607-S (G1)

Module series:  

AS-M1443 (G1),  

AS-M1443 (M6)

Load: 

positive 5400Pa 

negative 2400 Pa

Load 

positive 5400 Pa

negative 2400 Pa

Module series:  

AS-M1443 (G1),  

AS-M1443 (M6)

Module series:  

AS-M4327-S(G1) 

AS-M4327-S(G1)* 

Load: 

positive 2400Pa 

negative 2400 Pa

Load: 

positive 5400Pa 

negative 2400 Pa 

*

=add in case of extreme environmental conditions 

Module series:  

AS-M1443 (G1)

Module series:  

AS-M1443 (M6)

(Pitch bolt) Load: 

positive 2400Pa 

negative 2400 Pa

(Pitch bolt) Load: 

positive 2400Pa 

negative 1700 Pa

400 mm

400 mm

Figure 5: Bolting, loading capacity scheme

PV module

Frame

Mounting 

 rails

Clamp B

Flat washer

Spring washer

Nut

Flat washer

Bolt

PV module

Mounting structure

Bolt

Flat washer

Clamp

Nut

Spring washer

*

*

*

*

Содержание AS-M 2 Series












Отзывы: