background image

3

AEG STANDARD MODULE INSTALLATION MANUAL

GD202104 V1-21

EN

Icon

Meaning

Instruction

Prohibited

Damage may occur in case of 
noncompliance with the 
requirement.

Note

Useful information for 
product maintenance and 
operation is provided

Table 1: Icon meaning

1.2 Product Identification

Each module can be identified by means of the 
following information:

Product Label 

It is placed on the module backside. According to 
EN 50380 Directives it provides information about 
the main parameters of the module: Product Type, 
Maximum Power, Current at Maximum Power, Voltage 
at Maximum power, Open Circuit Voltage, Short Circuit 
Current -as measured under Standard Test Conditions, 
Maximum System Voltage, Maximum Series Fuse etc. 
The product label also features the Product Name 
Code (PNC).  

MONOCRYSTALLINE
PHOTOVOLTAIC 
MODULE

Brückenstrasse 94
60594 Frankfurt am Main
Deutschland / Germany

Product assembled in People's Republic of China.

PV Module classification

AEG is a registered trademark used under 

license from AB Electrolux (publ).

Solar Solutions GmbH

 

Class II

www.aeg-industrialsolar.de  | +49 (0)69 400500810

Tolerance on Pmax
Tolerance on Voc
Tolerance on Isc

±3%
±3%
±4%

Measured at Standard Test 
Conditions (E=1000 W/m

2, 

Tc=25°C, AM=1.5) 

For field connection please use 
minimum Ø 4mm

2  

[12 AWG] 

copper wires insulated for a 
minimum temp. 90°C. 

Tested according to

IEC 61215-1:2016   IEC 61215-1-1:2016 

IEC 61215-2:2016  IEC 61730-1:2016 

IEC 61730-2:2016 

This photovoltaic module 
produces electricity when 
exposed to light. Please refer to 
the instructions stated in the 
mounting manual for proper use.

Hazardous electricity can shock, 
burn or cause death. 
Do not touch connectors!

Module Type
Maximum Power (Pmax)

Power Sorting
Open Circuit Voltage (Voc)

Short Circuit Current (Isc)

Maximum Power Voltage (Vmp)

Maximum Power Current (Imp)

Maximum System Voltage
Maximum Series Fuse

340

0 ~ 5

41.70

10.40

34.01

10.01

1000

20

W
W

V
A
V
A
V
A

AS-M1202-H(G1)-340

Figure 1: label example

Serial Number

  

Each individual module is identified by a unique serial 
number univocally coupled with a barcode. Serial 
number and barcode are permanently placed on the 
laminate, under the front glass of the module, and are 
visible from the module front.

Connector (+)

Connector (-)

Grounding 
holes 

(6-ø5.5)

Mounting
holes 

(10-9x14)

 

Drainage
holes

Label

Connectors

Drainage
holes

Junction
box

Mounting
holes 

Label

Grounding 
holes 

Figure 2: Examples of product technical drawings

Please refer to the specific product datasheet on   
www.aeg-industrialsolar.de for the latest technical data.

2. SAFETY

2.1 General safety 

All AEG PV modules should be installed according to 
all local and national applicable standards, codes and 
regulations. Only qualified personnel should install 
the solar modules. Installers bear the risk of all injury 
that might occur during installation including, without 
limitation, the risk of electric shock. Check and follow 
all safety precautions specified even for the other 
components of the system.

Look for any visible damage to the package or the 
product itself. Double-check the order information 
and the product nameplate to ensure the products 
are of the ordered type. Should you find any problems, 
contact the shipping company and / or your supplier as 
soon as possible before attempting product installation.

2.2 Handling safety 

Please observe the below indications when handling 
AEG solar modules: 
 
Store the pallets in a ventilated, dry location until 
installation. Do not open the module boxes during 
storage or transportation. Inappropriate transport and 
installation may void the warranty.

Do not apply paint or adhesive to module top 
surface.
Do not use mirrors or other magnifiers to 

artificially concentrate sunlight on the modules. 
Do not expose back sheet foils directly to sunlight.
Do not attempt to disassemble the modules
Do not remove any attached nameplates or components

Содержание AS-M 2 Series












Отзывы: