background image

5

73.976 | 09.47

EN

This device is not intended for use by persons (including children) with limited 

physical, sensory, or mental abilities, or inadequate experience and/or inad-

equate knowledge, unless supervised, or instructed on the use of the device, by 

a person responsible for their safety. Children should be supervised in order to 

ensure that they do not play with the device.
Lead-acid starter batteries may not be charged if the acid level is too high or too 

low, even if this only applies to one cell.

2.3  Data security

The user is responsible for the data security of changes to the factory settings. 

The manufacturer is not liable in the event of deleted personal settings.

2.3  Other risks

 NOTE

Danger of fire and explosion

Do not use the battery charger in dusty environments, in the vicinity of solvents, or 

where inflammable gases and vapours can occur.
No open fires, flames or sparks in the vicinity of the batteries.
Ensure that the room is adequately ventilated.
Check the charging process regularly.
Follow the charging instructions of the battery manufacturer.
Never charge a frozen battery. 
The  applicable  standards  for  battery  charging  stations  and  battery  charging 

rooms are to be observed.

 NOTE

Battery acid

Acid splashes on skin or clothing should be immediately treated with soap suds 

and rinsed with plenty of water.
If acid splashes into the eyes, immediately rinse with plenty of water and seek 

medical advice.
Ensure that the battery is in a secure and stable position, because if the battery 

were to tip over or fall, acid would escape.

2.4  Fault behaviour

In the following situations, it is dangerous to operate the battery charger and it 

must be disconnected from the mains immediately:

The battery charger does not appear to function at all, even though the mains 

switch is on.
The battery charger, mains cable, or charging cable is visibly damaged.
Emission of smoke or fluid penetration occurs.
Parts are loose.

In these situations, inform the manufacturer, the manufacturer's customer 

service, or a similarly qualified person, in order to prevent endangerment.

2.5  Exclusion of liability

The manufacturer can neither monitor the compliance with this manual nor the 

conditions and methods during the installation, operation, and usage of the 

battery charger. Improper installation of the system may result in damage to 

property and, as a consequence, bodily injury.
Therefore, we assume no responsibility or liability for loss, damage or costs 

which result from, or are in any way related to, incorrect installation, improper 

operation, or incorrect use.
Similarly, we assume no responsibility for patent right infringements or other 

infringements of the rights of third parties caused by usage of this battery charger.
The manufacturer reserves the right to make changes to the product, technical 

data or assembly and operating instructions without prior notice.



Содержание Stecamat STM 820





















Отзывы: