Advantech iDAQ-934 Скачать руководство пользователя страница 5

Страница: 5 / 54

iDAQ-934_964 User Manual

Safety Instructions

Read these safety instructions carefully.

Retain this user manual for future reference.

Disconnect the equipment from all power outlets before cleaning. Use only a

damp cloth for cleaning. Do not use liquid or spray detergents.

For pluggable equipment, the power outlet socket must be located near the

equipment and easily accessible.

Protect the equipment from humidity.

Place the equipment on a reliable surface during installation. Dropping or letting

the equipment fall may cause damage.

The openings on the enclosure are for air convection. Protect the equipment

from overheating. Do not cover the openings.

Ensure that the voltage of the power source is correct before connecting the

equipment to a power outlet.

Position the power cord away from high-traffic areas. Do not place anything over

the power cord.

10.

All cautions and warnings on the equipment should be noted.

11.

If the equipment is not used for a long time, disconnect it from the power source

to avoid damage from transient overvoltage.

12.

Never pour liquid into an opening. This may cause fire or electrical shock.

13.

Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14.

If any of the following occurs, have the equipment checked by service person

nel:

–

The power cord or plug is damaged.

–

Liquid has penetrated the equipment.

–

The equipment has been exposed to moisture.

–

The equipment is malfunctioning, or does not operate according to the user

manual.

–

The equipment has been dropped and damaged.

–

The equipment shows obvious signs of breakage.

15.

Do not leave the equipment in an environment with a storage temperature of

below -20° C (-4° F) or above 60° C (140° F) as this may damage the compo

nents. The equipment should be kept in a controlled environment.

16.

CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only

with the same or equivalent type as recommended by the manufacturer. Discard

used batteries according to the manufacturer’s instructions.

17.

In accordance with IEC 704-1:1982 specifications, the sound pressure level at

the operator’s position does not exceed 70 dB (A).

DISCLAIMER: These instructions are provided according to IEC 704-1 standards.

Advantech disclaims all responsibility for the accuracy of any statements contained

herein.

Содержание iDAQ-934























































Результаты поиска

Содержание iDAQ-934

Отзывы:

Похожие инструкции для iDAQ-934

Бренды по названию

Популярные бренды

Advantech iDAQ-934, Руководство пользователя

Результаты поиска

Содержание iDAQ-934

Отзывы:

Похожие инструкции для iDAQ-934

Бренды по названию

Популярные бренды