Advantech EKI-7657C Скачать руководство пользователя

Страница: 79 / 110

69 Chapter3

•

Pull down the selection item and focus on

802.1Q

then press

Apply

to set the VLAN Operation

Mode in

802.1Q

mode.

•

Enable GVRP Protocol:

Tick the checkbox to enable GVRP protocol. This checkbox is available while

the VLAN Operation Mode is in

802.1Q

mode.

•

Management VLAN ID:

The default value is ‘0’ which means VLAN function in 802.1Q mode is not

available. While this column field is filled with a value from 1 to 4096, the member ports of this VLAN
can access the management interface.

•

Select the port you want to configure.

•

Link Type:

there are 3 types of link type.

Access Link:

Single switch only,

it allows the user to group ports by assigning the same

Untagged VID. While this link type is set, the Untagged VID column field is available but the
Tagged VID column field is disabled.

Trunk Link:

The extended application of

Access Link

. It allows the tagged frames go across

two or more switches by assigning the tag with VID to the frames. Having set this link type, the
Tagged VID column field is available but the Untagged VID column field is disabled.

Hybrid Link

: Both Access Link and Trunk Link are available.

•

Untagged VID:

Assign the untagged frame VID.

•

Tagged VID:

Assign the tagged frame VID.

•

Click

Apply

to have the settings taken effect.

Figure 3.37: 802.1Q VLAN Configuration

Group Configuration

Edit the existing VLAN Group.

•

Select the VLAN group in the table list.

Содержание EKI-7657C















































































































Результаты поиска

Содержание EKI-7657C

Отзывы:

Похожие инструкции для EKI-7657C

Бренды по названию

Популярные бренды

Advantech EKI-7657C, Руководство пользователя

Результаты поиска

Содержание EKI-7657C

Отзывы:

Похожие инструкции для EKI-7657C

Бренды по названию

Популярные бренды