Advantech EKI-7657C Скачать руководство пользователя | Manualshive

Страница: 75 / 110

background image

65 Chapter3

3.2.3 Protocol

The user can set the layer 2 protocol setting via this interface.

VLAN configuration

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow
you to isolate network traffic, so only the members of the same VLAN will receive traffic from the ones of
the same VLAN. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group
of network devices to another Layer 2 switch. However, all the network devices are still plugged into the
same switch physically.

The switch supports

Port-based

and

802.1Q

(tagged-based) VLAN. The default configuration of VLAN

operation mode is “

Disable

”.

Figure 3.33: VLAN Configuration

VLAN configuration - Port-based VLAN

Packets can go among only members of the same VLAN group. Note all unselected ports are treated as
belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored.

In order for an end station to send packets to different VLAN groups, it itself has to be either capable of
tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of
classifying and tagging the packet with different VLAN ID based on not only default PVID but also other
information about the packet, such as the protocol.

«
...
73
74
75
76
77
...
»

Содержание EKI-7657C















































































































Отзывы:

Нет отзывов

Похожие инструкции для EKI-7657C

Бренд: Communica Страницы: 5

Бренд: DANLERS Страницы: 2

Бренд: LEGRAND Страницы: 2

MyPower S2300-28TC-AC

Бренд: Maipu Страницы: 31

Бренд: Adler Страницы: 8

PowerSwitch Z9332F-ON

Бренд: Dell EMC Страницы: 16

Бренд: Dahua Страницы: 15

Бренд: Lantech Страницы: 24

Бренд: Tenda Страницы: 177

Storage Networking SAN128B-6

Бренд: IBM Страницы: 116

Personal MiniHub

Бренд: Black Box Страницы: 22

Бренд: PIKA Страницы: 7

Бренд: Optone Страницы: 10

IMI SENSORS EX686B77

Бренд: PCB Piezotronics Страницы: 63

Бренд: Anybus Страницы: 126

Бренд: Comtrend Corporation Страницы: 2

Бренд: Kramer Страницы: 2

Бренд: Hama Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды