Advantech EKI-1242 Series Скачать руководство пользователя страница 51

Страница: 51 / 64

EKI-1242 Series User Manual

The following figure displays the menu as found in the EKI-1242PNMS/EKI-

1242IPNMS.

Figure 3.15 Network Setting > IP Setting

The following table describes the items in the previous figure.

IP Address

Enter a value to specify the IP address of the interface. The default is

192.168.1.1.

Subnet Mask

Enter a value to specify the IP subnet mask for the interface. The

default is 255.255.255.0.

Gateway

Enter a value to specify the default gateway for the interface. The

default is 192.168.1.254.

Item

Description

Modbus/TCP IP Address Setting
Mode

Click the drop-down menu to select the IP address setting mode:

Static address, or DHCP client.

IP Address

Enter a value to specify the IP address of the interface. The default is

192.168.1.1.

Subnet Mask

Enter a value to specify the IP subnet mask for the interface. The

default is 255.255.255.0.

Gateway

Enter a value to specify the default gateway for the interface. The

default is 192.168.1.254.

PROFINET
Mode

Displays the IP address setting mode of the device.

IP Address

Enter a value to specify the IP address of the interface. The default is

0.0.0.0.

Subnet Mask

Enter a value to specify the IP subnet mask for the interface. The

default is 0.0.0.0.

Gateway

Enter a value to specify the default gateway for the interface. The

default is 0.0.0.0.

Item

Description

Содержание EKI-1242 Series

































































Результаты поиска

Содержание EKI-1242 Series

Отзывы:

Похожие инструкции для EKI-1242 Series

Бренды по названию

Популярные бренды

Advantech EKI-1242 Series, Руководство пользователя

Результаты поиска

Содержание EKI-1242 Series

Отзывы:

Похожие инструкции для EKI-1242 Series

Бренды по названию

Популярные бренды