manualshive.com logo in svg

Advantage Controls MICROtron MICRO-C, Руководство пользователя

Поделиться
Скачать
Advantage Controls MICROtron MICRO-C Скачать руководство пользователя страница 12

12

Conductivity Sampling Methods

 

A.   Continuous

 - Typical for most tower applications.  The controller is constantly reading the sensor 

and activating the bleed relay based on readings relationship to the set point, set point direction 

and differential.  Example:  A rising set point of 1500 and differential of 50 the bleed relay would 

activate when the conductivity rises above 1500 and stays on until the reading drops to 1450.

B.   Timed Sampling

 - A sample timer allows the conductivity to be sampled at periodic intervals.

 

Sample intervals are adjustable from 1 minute to 99 hours, 59 min. Sample duration (on-time) is 

adjustable from 1 second to 99 minutes, 59 seconds.  If the reading is below the set point by the 

differential amount the bleed relay will be turned off at the end of the sample duration and the 

sample interval countdown started.  If the reading is above the set point at the end of the sample 

method the bleed relay stays on until the reading drops by the differential amount.

Calibration Overview

The MICRO-C controllers update the conductivity reading every two seconds with a running average.  If a probe 

is quickly exposed from one extreme reading to another, allow up to 30 seconds for the averaging to cycle 

and the current reading to stabilize.  MICROtron controller’s conductivity scale should be selected so that the 

conductivity setpoint is as close as possible to the middle of the scale.  (See page 9 menu for setting scale).

Note:  If a controller is using Timed Sampling method of control the conductivity reading shown in the 

RUN mode may not be a current reading.  The controller will hold and display the conductivity value 

seen at the end of the last sample or hold duration.  To see a current reading force on the bleed relay 

with either the Force button or via the Calibration menu.

A.   Continuous

 - Calibrating continuous sampling units can be done at any time with the probe in a 

steady stream of water with no air or steam present.

B.   Timed Sampling

 - While in the calibration menu there is a selection to force on the bleed relay.  

It will force it into the sample period.  After 1-2 minutes verify that the reading is stable then enter 

the desired calibration value.

Notes: 

1.  If you change the conductivity scale in the Configure menu you MUST then go to Diagnostics 

and Reset the Cal then go to the Calibration menu and calibrate accordingly.

Содержание MICROtron MICRO-C

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды