Advantage Controls GF with MegaTron XS Скачать руководство пользователя страница 9

Страница: 9 / 28

Step 8:

Set the

HIGH ALARM

settings for

VALUE

(the reading

that will give a High Alarm) and

NOTIFICATION

. Press

ENTER

to confirm and go to the previous page

>mA INPUT 1 HIGH ALARM<

VALUE

ALARM NOTIFY

High Alarm 00020 %)

[__ ] %

USE NUMBER KEYS TO CHANGE, PRESS

ENTER TO ACCEPT OR BACK TO ERASE

Step 9:

Set the value of the

ALARM NOTIFY

by using the

arrow keys. Then press

ENTER

to confirm and go to the

previous screen.

Note:

Display - will appear on controller display only,

Remote - appears through email if controller is online, or

both Dis/Remote

>mA INPUT 1 HIGH ALARM<

VALUE

ALARM NOTIFY

ALARM NOTIFY (OFF )

--> OFF

USE UP/DOWN KEYS TO CHANGE

PRESS ENTER TO ACCEPT

Step 10:

Repeat Steps 19 and 20 for the

LOW ALARM

Press

BACK

to return the mA Input 1 Set Points

>mA INPUT 1 SETPOINT CHANGE<

SET POINT

DIFFERENTIAL

HIGH ALARM

LOW ALARM

LIMIT TIME

Step 11:

Set the value of

LIMIT TIME

by using the number

keys. Then press

ENTER

to confirm and go to the

previous screen. The Limit Time and the Alarm

Notification will need to be set. Press

HOME

when finished to return to the

HOME

>mA INPUT 1 SETPOINT CHANGE<

SET POINT

DIFFERENTIAL

HIGH ALARM

LOW ALARM

LIMIT TIME

Note:

If the Limit Time is met a relay activated by

the 4-20mA input will be forced off until the Set

Point has been satisfied and reset.

Содержание GF with MegaTron XS





























Результаты поиска

Содержание GF with MegaTron XS

Отзывы:

Похожие инструкции для GF with MegaTron XS

Бренды по названию

Популярные бренды

Advantage Controls GF with MegaTron XS, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание GF with MegaTron XS

Отзывы:

Похожие инструкции для GF with MegaTron XS

Бренды по названию

Популярные бренды