manualshive.com logo in svg

Advanjet HM-2600, Техническое обслуживание и ремонт

Поделиться
Скачать
Advanjet HM-2600 Скачать руководство пользователя страница 3

Table of Contents 

3.4

 

Reassemble the Heater Block .................................................................................................... 20

 

3.4.1

 

Install New Heater Seal and Washer ............................................................................. 20

 

3.4.2

 

Install New Spring .......................................................................................................... 20

 

3.4.3

 

New Heater Block Bearing ............................................................................................. 20

 

3.4.4

 

Position Heater Block .................................................................................................... 20

 

3.4.5

 

Attach Heater Block ....................................................................................................... 20

 

3.4.6

 

(Optional) Connect New Heater Block ........................................................................... 20

 

3.5

 

Attach the Valve Mount ............................................................................................................... 21

 

3.5.1

 

Verify O-Rings................................................................................................................ 21

 

3.5.2

 

Install Valve Mount Screws ............................................................................................ 21

 

3.6

 

(Optional) Replace Melter Cable ................................................................................................ 22

 

3.6.1

 

(Optional) Remove the Melter Cable ............................................................................. 22

 

3.6.2

 

(Optional) Identify Cartridges on New Melter Cable ...................................................... 22

 

3.6.3

 

(Optional) Shorter Heater Cartridge .............................................................................. 22

 

3.6.4

 

(Optional) Longer Heater Cartridge ............................................................................... 22

 

3.6.5

 

 (Optional) Install Cartridges and Tighten Setscrews .................................................... 22

 

3.7

 

Reassemble the Jet .................................................................................................................... 23

 

3.7.1

 

Insert the Nozzle Plate Screws ...................................................................................... 23

 

3.7.2

 

Position the Melter Assembly ........................................................................................ 23

 

3.7.3

 

Position the Top Cover .................................................................................................. 23

 

3.7.4

 

Attach Top Cover ........................................................................................................... 23

 

3.7.5

 

Connect the Melter ........................................................................................................ 23

 

3.7.6

 

Install Feed Tube Spacer ............................................................................................... 23

 

3.7.7

 

Attach Upper Feed Tube Enclosure .............................................................................. 23

 

3.7.8

 

Tuck the Cables ............................................................................................................. 24

 

3.7.9

 

Trim the Cables.............................................................................................................. 24

 

3.7.10

 

Connect the Air Valve .................................................................................................... 24

 

3.7.11

 

Position Mounting Plate ................................................................................................. 24

 

3.7.12

 

Attach the Mounting Plate .............................................................................................. 24

 

3.7.13

 

Attach the Dovetail Plate ............................................................................................... 24

 

4.

 

SET THE JET HAMMER GAP ............................................................................................................. 25

 

4.1

 

Using the Gap Set Fixture .......................................................................................................... 25

 

4.2

 

Prepare the Gap Set Fixture ....................................................................................................... 26

 

4.2.1

 

Check the Zeroing Plate ................................................................................................ 26

 

4.2.2

 

Zero the MIcrometer ...................................................................................................... 26

 

4.2.3

 

Remove the Zeroing Plate ............................................................................................. 26

 

4.2.4

 

Attach the Jet ................................................................................................................. 26

 

4.3

 

Measure the Gap ........................................................................................................................ 27

 

4.3.1

 

Connect the Jet .............................................................................................................. 27

 

4.3.2

 

Reading the Dial ............................................................................................................ 27

 

4.4

 

Adjust the Gap ............................................................................................................................ 27

 

GRACO STANDARD WARRANTY ........................................................................................................... 28

 

 

3A6328A 

Advanjet HM-2600 Hotmelt Jet Maintenance and Repair 

Page 3 of 28 

Содержание HM-2600





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды