background image

3.5 Heater Cartridge / Thermocouple Replacement .................................................................. 20

 

3.6 Description of Anti-jam Circuit .......................................................................................... 20

 

3.7 Anti-jam Adjustments / Testing .......................................................................................... 20

 

3.8 Preventative Maintenance ................................................................................................... 21

 

Chapter 4:

 

Parts Identification 

22

 

4.1 Recommended Spare Parts List .......................................................................................... 23

 

4.2 Parts / Component Identification......................................................................................... 23

 

4.3 Pneumatic Diagram ............................................................................................................. 23

 

4.4 Wiring Diagram................................................................................................................... 23

 

A.

 

T-200 System Layout ..................................................................................................... 24

 

B.

 

T-200 Electronics Assembly .......................................................................................... 25

 

C.

 

T-200 Heater Bar Assembly ........................................................................................... 27

 

D.

 

T-200 Main Frame Assembly ........................................................................................ 29

 

E.

 

T-200 Adjustable Chute Assembly ................................................................................ 32

 

F.

 

T-200 Pneumatic Layout ................................................................................................ 33

 

G.

 

T-200 Electrical Layout ................................................................................................. 34

 

 
 
 

 


 

Содержание T-200




































Отзывы: