Advanced Measurement Technology 142AH Скачать руководство пользователя страница 5

Страница: 5 / 16

DANGER

Opening the cover of this instrument is likely to expose dangerous voltages. Disconnect the
instrument from all voltage sources while it is being opened.

WARNING Using this instrument in a manner not specified by the manufacturer may impair the

protection provided by the instrument.

CAUTION To prevent moisture inside of the instrument during external cleaning, use only enough liquid

to dampen the cloth or applicator.

SAFETY WARNINGS AND CLEANING INSTRUCTIONS

Cleaning Instructions

To clean the instrument exterior:

Unplug the instrument from the ac power supply.

Remove loose dust on the outside of the instrument with a lint-free cloth.

Remove remaining dirt with a lint-free cloth dampened in a general-purpose detergent and water
solution. Do not use abrasive cleaners.

Allow the instrument to dry completely before reconnecting it to the power source.

Содержание 142AH

















Результаты поиска

Содержание 142AH

Отзывы:

Похожие инструкции для 142AH

Бренды по названию

Популярные бренды

Advanced Measurement Technology 142AH, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 142AH

Отзывы:

Похожие инструкции для 142AH

Бренды по названию

Популярные бренды