Advanced Energy iLS1500 Series Скачать руководство пользователя страница 50

Страница: 50 / 54

iLS600, iLS600-R and iLS1500 Series

Rev. 05.20.21_#1.0

advancedenergy.com

SYSTem:AOUTput:MODE <DISabled|PARallel|SERies>

— This command controls the

function of the analog output of the power supply to facilitate series or parallel operation. In

parallel mode the analog output is proportional to the output current of the power supply, in

series mode the analog output is proportional to the output voltage of the power supply.

SYSTem:AOUTput:Mode?

— This command returns the current state of the analog output

of the power supply.

SYSTem:CAPability?

— Display the unit capability string. For BENCH iLS, the string

(DCPSUPPLY WITH MEASURE) is returned.

SYSTem:CONFiguration:SAVE

— This command saves configuration parameters to

non-volatile memory. Contents consist of:

•

Analog current scaling select (3V/5V/10V)

•

Analog current calibration slopes

•

Analog voltage scaling select (3V/5V/10V)

•

Analog voltage calibration slopes

•

Auto-start (Enabled/Disabled)

•

Calibrated flag (Calibrated/Not Calibrated)

•

Control source (Local/Remote/Remote with Lock/Analog Voltage Control/Analog

Current Control/Analog Dual Control)

•

Conversion current user slope and offset

•

Conversion current factory slope and offset

•

Conversion voltage user slope and offset

•

Conversion voltage factory slope and offset

•

Model

•

Over-current protection level

•

Over-power protection level

•

Over-voltage protection level

•

Power setpoint

•

Remote sense (Enabled/Disabled)

APPENDIX

Содержание iLS1500 Series























































Результаты поиска

Содержание iLS1500 Series

Отзывы:

Похожие инструкции для iLS1500 Series

Бренды по названию

Популярные бренды

Advanced Energy iLS1500 Series, Руководство пользователя

Результаты поиска

Содержание iLS1500 Series

Отзывы:

Похожие инструкции для iLS1500 Series

Бренды по названию

Популярные бренды