Advanced Energy iLS1500 Series Скачать руководство пользователя страница 41

Страница: 41 / 54

iLS600, iLS600-R and iLS1500 Series

Rev. 05.20.21_#1.0

advancedenergy.com

•

Temperature Error



Output Board Over-Temperature



Primary Board Over-Temperature



Fan stall

•

Watchdog Error

Execution Error (not used)

Command Error (not used)

User Request (not used)

128 Power On (not used)

The command *ESE 0 clears this register.

*ESE?

— Returns the present contents of the Standard Event Status Enable Register. The

contents are described in the description of *ESE. If multiple bits are set, the result is the

sum of the set bit values.

*ESR?

— Returns the present contents of the Standard Event Status Event Register.

*IDN?

— Returns the identification string for this unit. The string will contain:

•

Company name – “Artesyn Power”

•

Model – For example “Bench 100-10 iLS”

•

Unit serial number. For example, “031418032001”.

•

Control/Interface processor software revisions. For example,

“1.00.0051/1.00.1361”.

Fields are separated by commas. Serial numbers and software revisions are separated
by forward slashes.

*OPC

— This command triggers the Operation Complete Flag in the Standard Event Status

Event Register.

APPENDIX

Содержание iLS1500 Series























































Результаты поиска

Содержание iLS1500 Series

Отзывы:

Бренды по названию

Популярные бренды

Advanced Energy iLS1500 Series, Руководство пользователя

Результаты поиска

Содержание iLS1500 Series

Отзывы:

Бренды по названию

Популярные бренды