CS2-CT-2010-10-03
C2-17
-4/8
Offset function:
Fine zero & span adjustment:
When the
[
oFset
]
in
[
input group
]
set to be
200
:
Totalizer will be reset to “200”, when ECI is closed. The
Totalizer will count-up from 200.
Users can get Fine Adjustment of analogue output by front key of the
meter. Please connect standard meter to the terminal of analogue
output. To press the front key(up or down key) of meter to adjust and
check the output.
Zero adjust [
aOzro
]
:
Fine Zero Adjustment for Analog Output;
Settable range: -38011~27524;
Span adjust [
aOspn
]
:
Fine Span Adjustment for Analog Output;
Settable range: -38011~27524;
Reset for Totalizer(Energy)
Reset by ECI
Edge Trigger
O
N
ON
ON
Totalizer
reset
[
ecI_
]
200
[
ofset
]
RS 485 communication(option)
Banks selection function(option):
There are extra 3 banks can be selected by E.C.I.
E.C.I.1 close means bank 1 has been selected.
E.C.I.2 close means bank 2 has been selected.
E.C.I.3 close means bank 3 has been selected.
E.C.I. all open means bank 0 has been selected.
CS2 series supports Modbus RTU mode
protocol to be used as Remote
Terminal Unit (RTU) for monitoring and controlling in a SCADA (Supervisor
Control And Data Acquisition) system. The baud rate can be up to 38400
bps. It's not only can be read the measured value and DI (external control
inputs) status but also controls the relays output (DO) by RS485
communication ports.
Debouncing time:
The function is for avoiding noise signal to into the meter. And The basic
period is 8 m-seconds. It means you set the number that has to multiple
8 m-seconds.
For example:
[
debnc
]
set to be 5, it means 5 x 8mseconds = 40mseconds
Analogue output(option)
Please specify the output type either a 0~10V or 4(0)~20mA in ordering.
The meter offers one analogue output with Multi-Cross selection function.
User can program the output to correspond immediately value, totalizer,
batch and batch count, and also the output low and high can be
programmable which it's related to various display values easier in
[
ao
group
]
.
Reverse slope output is possible by reversing point positions. Please refer
to the detail description as below,
CS2-CT & CS2-PR APPLICATION FOR FLOWNETER / PRESSURE MEASURING
RS 485 Modbus RTU Mode (up to 38400bps)
Analog Output 0~10V/0(4)~20mA
3 External Control Input:
Functions:
Relative PV / PV Hold / Reset Max or Mini.
Hold /
DI
/ Reset for Relay Energized Hold
Application:
Thermal Switch / Circuit Breaker / Push
Button / ……
Display:
Mode:
Measuring Value / Maximum Hold / Minimum
Hold / Reading value from RS485 command
AL
AL
Flowmeter
R L 1
R L 2
R L 3
R L 4
COM
ECI1
ECI2
ECI3
ENT/FN
◄
▲
▼
Kg/
Pulse
RL2
2
R L 3
R L 4
COM
CI11
CI2
CI3
ENT/FN
◄
▲
▼
Output range:
Voltage: 0~5V / 0~10V / 1~5V programmable
Remote Display:
Current: 0~10mA / 0~20mA / 4~20mA programmable
Functions:
Output High / Low scale, output limit, fine adjustment
Output range high
[
aOhs
]
:
To setting the Display value High to versus output range
High(as like as 20mA in 4~20)
The meter will show the value that received from RS485 command. In
past, The meter normally receive 4~20mA or 0~10V from AO or digital
output from BCD module of PLC .We support a new solution that PV
shows the value from RS485 command of master so that can be
save
cost and wiring
from PLC.
Output range low [
aOls
]
:
To
setting the Display value Low to versus output range
Low(as like as 4mA in 4~20)
When the
[
dsply
]
set to be RS485, it means, the PV screen will show the
number from RS485 command & data. The data (number) will be same as
PV that will make the totalizer accumulate and compare with set-point,
analogue output and ECI functions so that is to control analogue output,
relay energized and so on.
CS2-CT APPLICATION FOR REMOTE DISPLAY FROM RS485 COMMAND
RS 485 Modbus RTU Mode (up to 38400bps)
RS485 wiring 1.2KM maximum
Terminate Resistor:
R L 1
R L 2
RL3
RL4
COM
ECI1
ECI2
ECI3
ENT/FN
◄
▲
▼
Kg/cm
2
R L 1
RL2
2
R L 3
R L 4
COM
CI11
CI2
CI3
ENT/FN
◄
▲
▼
Set Scaling: [
lOsc
]: 0.00, [
hIsc
]: 199.99;
Output: [
aOls
]: 50.00(Display Value Low),
[
aOhs
]: 150.00(Display Value High)
0.00%
100.00%
50.00%
OUTPUT
199.99
100.00
0.00
50.00
150.00
SCALE
[
aOls
]
[
aOhs
]
The range between
[
aOhs
]
and
[
aOls
]
should be over
20% of span at least; otherwise, it will be got less resolution of
analogue output.
Output High Limit [
aOlmt
]
:
0.00~110.00% of output High User can set the high limit of
output to avoid a damage of receiver or protection system.
Set Scaling: [
lOsc
]: 0.00, [
hIsc
]: 199.99;
Output: [
aOls
]: 50.00(Display Value Low),
[
aOhs
]: 150.00(Display Value High)
[
aOlmt
]: 80.00%( of Output Range)
0.00%
100.00%
50.00%
OUTPUT
199.99
100.00
0.00
50.00
150.00
SCALE
Ao.LMt: 80.00%
80.00%
[
aOhs
]
[
aOls
]
[
aOlmt
]
CSM-321S
CS2-
V
A
CSM-321S CSM-
CSM-
CS2-CT
CSM-321S CSM-
CSM-
CSM-321S
CSM-
CSM-321S
