CS2-CT-2010-10-03
C2-17
-5/8
OPTIONAL FUNCTION
Customize function with quantities is welcome. Please contact with our
sales for detail. The appendix code of optional function will be add
behind the code of auxiliary power as like as xxx-A-3BK.
BANK FUNCTION(Suffix-3BK)
●
The function is for CS2 to control difference process with a same
meter.
●
For example; a pressure testing equipment; it has to measure
multi-range with difference pressure transducers. The meter can be
pre-set 4 groups parameter to show difference scale and relay
energized in difference set-points. The operator just selects the
bank number (bank1) to meet the process (product A). To make
easier operating and to avoid mistake in process.
●
The bank function is available in CS2-CT (optional) too. It’s useful to
control as like as filling machine, Air flow measurement with
difference sensor.
●
4 banks pre-set for all relay functions relative 4 difference scaling,
decimal point, and select by 3 External Control Inputs(E.C.I.) or
front key.
●
Example:
Product A
: Flowmeter: 1.0000L/sec; Set-Point: 2.0000L
Output: RS485
Product B
: Flowmeter: 5.000L/sec; Set-Point: 6.000L
Output: RS485
Setting:
BANK1:
[
dp
]
:
)0000
[
ry!md
]
:
totLr
[
ry!sp
]
:
@0000
[
ry!ot
]
:
)0)5
0(M).00.5(S)
BANK2:
[
dp
]
:
)000
[
ry!md
]
:
totLr
[
ry!sp
]
:
^000
[
ry!ot
]
: 0
)0!0
(M).01.0(S)
ECI.1
: Bank.1
ECI.2
: Bank.2;
connect to a selector (or DO of PLC) to ECI1 and ECI2
X
The order want to produce
Product A,
to switch selector to A(Label
A
on
panel), and then ECI.1 close, the square green LED bright. The meter will
work base on the setting of bank1 and relay1 output on 2.0000.
X
The second order want to produce
Product B,
to switch selector to
B(Label
B
on panel), and then ECI.2 close, the square green LED
bright. The meter will work base on the setting of bank2 and relay1
output on 6.000.
●
Only 1 Bank can be selected. The priority is Bank1 > Bank2 > Bank3, if it
is double selection.
ERROR
MESSAGE
BEFORE POWER ON, PLEASE CHECK THE SPECIFICATION AND CONNECTION AGAIN.
SELF-DIAGNOSIS AND ERROR CODE
:
DISPLAY
DESCRIPTION
REMARK
ovfl
Display is positive-overflow (Signal is over display range)
(Please check the input signal)
-ovfl
Display is negative-overflow (Signal is under display range)
(Please check the input signal)
ovfl
ADC is positive-overflow (Signal is higher than input
range
high 20%
)
(Please check the input signal)
-ovfl
ADC is negative-overflow (Signal is lower than input
range low
-20%
)
(Please check the input signal)
eep
fail
EEPROM occurs error
(Please send back to manufactory for repaired)
aiCng
pv
Calibrating Input Signal do not process
(Please process Calibrating Input Signal)
aic
fail
Calibrating Input Signal error
(Please check Calibrating Input Signal)
aoCng
pv
Calibrating Output Signal do not process
(Please process Calibrating Output Signal)
aoc
fail
Calibrating Output Signal error
(Please check Calibrating Output Signal)
CSM-321S
CS2-
V
A
CSM-321S CSM-
CSM-
CS
2-
CT
CSM-321S CSM-
CSM-
CSM-321S
CSM-
CSM-321S
