ADLINK Technology STC2-10WP-AL Скачать руководство пользователя страница 39

Страница: 39 / 121

STC2-AL/KL Series

4.4 Advanced Menu

This menu contains the settings for most of the user interfaces in

the system.

4.4.1

Advanced > CPU Configuration

Feature

Options

Description

CPU Signature

Info only

Displays the CPU Signature

Microcode Patch

Info only

Displays the Microcode Patch

Max CPU Speed

Info only

Displays the CPU Speed

Min CPU Speed

Info only

Displays the Min CPU Speed

Processor Cores

Info only

Displays the number of Processor Cores

Intel HT Technology

Info only

Displays Intel HT Technology status

Intel VT-x Technology Info only

Displays Intel VT-x Technology status

L1 Data Cache

Info only

Displays the Processor L1 Data Cache size.

L1 Instruction Cache

Info only

Displays the Processor L1 Instruction

Cache size.

L2 Cache

Info only

Displays the Processor L2 Cache size.

L3 Cache

Info only

Displays the Processor L3 Cache size.

L4 Cache

Info only

Displays the Processor L4 eDRAM size.

VMX

Info only

VMX Supported or Not

SMX/TXT

Info only

SMX/TXT Supported or Not

Intel(R)

SpeedStep(tm)

Disabled

Enabled

Allows more than two frequency ranges to

be supported.

Turbo Mode

Disabled

Enabled

Enable/Disable processor Turbo Mode

(requires EMTTM enabled too). AUTO

means enabled, unless max turbo ratio is

bigger than 16 - SKL A0 W/A

C states

Enabled

Disabled

Enable/Disable CPU Power Management.

Allows CPU to go to C states when it's not

100% utilized.

Enhanced C-states

Disabled

Enabled

Enable/Disable C1E. When enabled, CPU

will switch to minimum speed when all

cores enter C-State.

Содержание STC2-10WP-AL


























































































































Результаты поиска

Содержание STC2-10WP-AL

Отзывы:

ADLINK Technology STC2-10WP-AL, Руководство пользователя, Страница: 39 / 121

Результаты поиска

Содержание STC2-10WP-AL

Отзывы: