ADLINK Technology PCI-8254 Скачать руководство пользователя страница 150

Страница: 150 / 226

136

Motion Control Theory

4.8 Interpolation

Interpolation is a multi-axes locus movement based on given locus

properties, e.g. center of circle and end point, and velocity data.

The controller then calculate relations between path and time. Axis

involved in interpolation start up at the same time and end at the

same time after operation completed.
This controller supports couple of interpolation including straight line

interpolation of any 2~6 axes, arc interpolation of any 3 axes and

spiral interpolation of any 3 axes.
The interpolation usually requires two or more axes to complete.

Required axes are assigned by array input. Here the axes array is

defined by assuming the first axis ID to be the reference axis.
Axis parameters of the reference axis is used as the basis for

setting up speed profiles of interpolation while settings of speed

profile are all in vector (composite). Take example. To execute a 2

axes straight line interpolation by Axis 1 and Axis 2, the axis ID

array can be declared as described below. In example below, the

first axis ID in axes_array is Axis 1. Then the interpolation

movement required initial speed, maximum speed, ending speed,

and acceleration rate are all set up relative to axis parameters of

Axis 1. If Axis 2 is the first element in axes_array then Axis 2 is the

reference axis.

I32 axes_array[2]

= { 1, 2 };

Sections below describe straight line, arc, and spiral interpolation

mechanism and operation and followed by continuous interpolation.

4.8.1

Linear Interpolation

This controller supports up to six axes straight line interpolation.

After the straight line interpolation command is received, all

relevant axes start up at the same time and move according to

specified (relative or absolute) position, speed, and acceleration

profiles, all relevant axes stop concurrently. The speed profiles are

set by synthetic vector.
Assume you want to make a N (N=2~6) axes straight line

interpolation with offset of each axes represented by

X0,

X1…

XN-1 then the synthetic shift

P shall be:

Содержание PCI-8254



































































































































































































































Результаты поиска

Содержание PCI-8254

Отзывы:

Похожие инструкции для PCI-8254

Бренды по названию

Популярные бренды

ADLINK Technology PCI-8254, Руководство пользователя

Результаты поиска

Содержание PCI-8254

Отзывы:

Похожие инструкции для PCI-8254

Бренды по названию

Популярные бренды