ADLINK Technology NuPRO-780 Series Скачать руководство пользователя

Страница: 13 / 43

Introduction

•

Memory size is controlled by device driver from 1 MB up to 11 MB

♦

PCI Bus Ethernet Interface:

•

Primary port : Built-in i815E chip +

82562EM (All of NuPRO-780

series)

•

Secondary port : Intel 82559 (For NuPRO-780DV only)

•

PCI local bus Ethernet controller

•

10/100Mbps operation in a single port PCI bus master architecture

•

IEEE 802.3 10base-T and 100base-TX compatible physical longer

support

•

IEEE802.3u

auto-negotiation

support for automatic speed selection

•

IEEE 802.3X (100base-TX Flow control support)

•

Wake on LAN support

•

External LAN status LED connectors

♦

Enhanced IDE:

Bus Master IDE controller, two EIDE interfaces for up

to four devices, support PIO Mode 3/4 or Ultra DMA/100 IDE devices,
including Hard Disk Drive, ATAPI CD-ROM, LS120, and ZIP drives.

♦

Super I/O Chipset: Winbond W83627HF

♦

Parallel Port:

•

One high-speed parallel port, SPP/EPP/ECP mode

•

ESD protection to 4KV

•

Downstream device protection to 30V

♦

Serial Port:

•

One 16550 UART compatible ports with RS-232 interface

•

One 16550 UART compatible ports with RS-232/422/485 (With

RS-485+ Auto-Direction Technology)

•

ESD protection to 2KV

♦

FDD Interface:

Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB,

2.88MB)

♦

USB Interface:

Two USB pin-header connectors, compliant with USB

Specification Rev. 1.1, Individual over-current protection

♦

AC’97 Link:

Содержание NuPRO-780 Series












































Результаты поиска

Содержание NuPRO-780 Series

Отзывы:

Похожие инструкции для NuPRO-780 Series

Бренды по названию

Популярные бренды

ADLINK Technology NuPRO-780 Series, Руководство пользователя

Результаты поиска

Содержание NuPRO-780 Series

Отзывы:

Похожие инструкции для NuPRO-780 Series

Бренды по названию

Популярные бренды