ADLINK Technology nanoX-EL Скачать руководство пользователя

Страница: 23 / 55

nanoX-EL User’s Guide

PICMG COM.0 R3.0

Page 23

4.2.

Signal Terminology Descriptions

Meaning of the terms used for signal description tables

Term

Description

Input to the module

Output from the module

I/O

Bi-directional Input / Output

Open drain output from the module

I 3.3V

Input 3.3V tolerant

I 5V

Input 5V tolerant

O 3.3V

Output 3.3V signal level

O 5V

Output 5V signal level

I/O 3.3V

Bi-directional signal 3.3V tolerant

I/O 5V

Bi-directional signal 5V tolerant

I/O 3.3V

Input or output 3.3V tolerant active in standby state

DDC

Display Data Channel

PCIE

PCI Express compatible differential signal

PEG

PCI Express Graphics

SATA

Serial ATA specification Revision 2.6 and 3

LVDS

Low Voltage Differential Signal - 330 mV nominal; 450 mV maximum differential signal

Power Input / Output

REF

Reference voltage output. May be sourced from a Module power plane.

PDS

Pull-down strap. A Module output pin that is either tied to GND or is not connected.
Used to signal Module capabilities to the Carrier Board.

PU (pull-up) resistor on module

PD (pull-down) resistor on module

Содержание nanoX-EL






















































Результаты поиска

Содержание nanoX-EL

Отзывы:

Похожие инструкции для nanoX-EL

Бренды по названию

Популярные бренды

ADLINK Technology nanoX-EL, Руководство пользователя

Результаты поиска

Содержание nanoX-EL

Отзывы:

Похожие инструкции для nanoX-EL

Бренды по названию

Популярные бренды