ADLINK Technology CoreModule 730 Скачать руководство пользователя

Страница: 27 / 36

Chapter 3

Hardware

CoreModule 730

Reference Manual

Utility Interface

The Utility interface provides three utility and I/O signals on the module and consists of a 5-pin, 0.100"

(2.54mm), single row header. The US15W SCH drives the signals on the Utility interface.

Table 3-9

provides the signal definitions.

•

Power Button

•

Reset Switch

•

Speaker

Power Button

The Utility header provides a signal for an external Power button through pins 1 and 2. The Power button

allows the user to turn Off the system.

Reset Switch

Pins 2 and 3 on the Utility header provide the signal for an external reset button which allows the user to re-

boot the system.

BIOS Recovery (Using Reset Switch)

In the event you have selected BIOS settings that prevent you from booting the system, you can stop the
current BIOS settings in the CMOS from being loaded by pressing and holding the Reset button for five

seconds and then releasing the button. The system re-boots, and the BIOS loads the default settings.

Speaker

The speaker signal provides sufficient signal strength to drive a 1W 8

“Beep” speaker through the Utility

interface at an audible level. The speaker signal is driven from an on-board amplifier and the SCH.

Note:

The shaded area denotes power or ground. The signals marked with * indicate active low.

Miscellaneous

Battery

An external battery connection is provided through the J17 header to support a backup battery for the CMOS
RAM and the RTC (Real Time Clock).

Real Time Clock (RTC)

The CoreModule 730 contains a Real Time Clock (RTC). The CMOS RAM can be backed up with a lithium

battery. If the battery is not present, a battery-free boot option in the BIOS completes the boot process and

resets the clock to the default date and time.

Table 3-9. Utility Interface Pin Signals (J25)

Pin #

Signal

Description

/PWR_BTN

External Power Button (Pins 1-2)

GND

Ground

/RESET SW*

External Reset Switch signal (Pins 2-3)

+5 Volts Power

SPKR_CONN

Speaker Output (Pins 4-5)

NOTE

Some operating systems require a valid default date and time to function.

Содержание CoreModule 730





































Результаты поиска

Содержание CoreModule 730

Отзывы:

Похожие инструкции для CoreModule 730

Бренды по названию

Популярные бренды

ADLINK Technology CoreModule 730, Справочное руководство

Результаты поиска

Содержание CoreModule 730

Отзывы:

Похожие инструкции для CoreModule 730

Бренды по названию

Популярные бренды