Adler Europe AD4503, Руководство пользователя, Страница: 6 / 76

* Normal - normal speed
2) Mount the container with the roller on the hooks on the back of the housing.
4. Press the button (3) to start air suction and vacuum welding. The button will automatically turn off when welding is finished.
USE OF THE DEVICE
Preparation of a bag from a roll of foil sleeve (open on both sides):
5) Lift the strip to cut the sleeve (15). Depending on the size of the products, cut the required length of the bag by moving the knife
holder (16).
a). Place the cut foil sleeve on the suction surface (6) so that it does not protrude behind the nozzles (10) as shown in the f
igure (D2.)
5. Disconnect the left and then the right lid opening buttons (4) first and lift the cover.
II. Extraction of air from external vacuum containers / bags
1) Insert the roll with the foil sleeve into the container (17) so that the film protrudes around 10 cm.
3. Press the button (13) to set the speed of the air suction:
The set includes a tube and two nozzles (14) for sucking air from vacuum containers (Fig. C).
2. Connect the container (not included) with the suction nozzle (10) using the tube (14).
I. Extraction and welding
1. Put the items in the bag. Place the other side on the suction surface (6). Close the cover by BOTH HANDS pressing (Fig. E) to hear
the "click" sound.
* Gentle - low speed (gentle)
1. Choose the right size tip and put on the tube (14)
2. By pressing the button select the type of product (1):
3. Press and hold button (11) continuously until you find that the vacuum is sufficient (Figure C).
4) Push the protruding foil between the lid hinges.
2. Use only ready-made bags (open on one side) or foil rolls in the form of a sleeve (open on both sides) inteded to vacuum sealing.
In order to obtain hermetic welding, the foil should be clean, dry and free of creases in the welding zone.
3) Open the welding machine cover by pressing the BOTH HANDS two buttons (4).
b). Close the lid by pressing BOTH HANDS (figure E) to hear the "click" sound and press the button (2), which will
automatically turn off after welding is completed.
c). Open the welding machine cover by pressing BOTH HANDS both buttons (4).
6) Seal one side of the cut sleeve forming the bag:
* Dry - dry
* Moist - moist
9. Seal 10. Suction nozzle
21. The butt welding machine is not suitable for packing liquids.
13. Adjusting the suction speed 14. Tube for evacuation of air from vacuum containers
11. Button for air extraction from the vacuum tank 12. Bring to standstill key
1. aximum width: 32 mm
7. Welding strip 8. Sealing sponge
17.Container for a foil sleeve roll
1. Product type setting 2. Seal control button
3. Air extraction & sealing button 4. Button for opening the cover
5. Cover lock 6. Suction surface
19. Do not underlay hands during you close the device.
15.Strip for cutting the foil sleeve 16. Knife holder for cutting the foil sleeve
Tips for ready-made bags or rolls (foil sleeve):
DESCRIPTION OF THE DEVICE (pic. A & B &C)
20. Do not use flammable objects.
Technical specifications:
1. Before cleaning, make sure that the device is connected to power.
NOTE: when extracting air from external vacuum containers, do not close the cover to avoid deformation of the gasket (9).
2. During cleaning, never immerse the appliance in water, only wipe it with a damp cloth.
Voltage: 220-240V ~50/60Hz
CLEANING AND MAINTENANCE
4. Take your finger off the button (11), disconnect the device and the external vacuum container.
Vacuum: -0,75 - -0.80 bar
Power: 130W
Welding together: 6-10 sec.
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
6