Adjust-a-Sink E140 Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 25

Adjust-a-Sink E140 Series Скачать руководство пользователя страница 5

Adjust-A-Sink® E140 System by Accessible Systems Inc. | Minneapolis, MN | 612-238-4600 | www.adjustasink.com

5 of 25

2D.

Install two 5/16” fasteners of

appropriate type and length through

the bottom row of mounting holes.

2E.

Unwrap the AC power cord as

needed and plug in to the intended

receptacle.

Press the switches on the upper

right of the lift unit and verify the

vertical travel and movement of the

slide section before continuing with

the installation.

Secure any excess supply cord so it

will not interfere with the slide

sections when in use.

TROUBLESHOOTING:

1. The linear actuator has built-it limit switches, so if it is at the end of travel, it will not move or make

any noise, try the reverse direction switch.

2. The linear actuator has a safety mechanism, so it only pushes the lift up, gravity pulls the lift down.

The slides on a new lift may be tight until break in, and the lift may not drop at this step of the

installation. The unit will drop with the full weight of the assembly and sink installed. You can

push down on the lift to get it back to the bottom position.

«
...
3
4
5
6
7
...
»

Содержание E140 Series


























Отзывы:

Нет отзывов