ADJ Products, LLC - www.adj.com - WiFly EXR HEX Par User Manual Page 11
WiFly EXR HEX Par Operating Instructions
the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 60 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display
can be read upside down.
1. Plug the fixture in and press the MODE button until “dXX” is dis-
played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “Stnd” or “rev” is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.
Operating Modes:
The WiFly EXR HEX Par has five operating modes:
• Sound Active mode - The unit will react to sound.
• Static Color Mode - There are 63 colors to choose from.
• RGBWA+UV Dimmer Mode - Choose one of the six colors to
remain static or adjust the intensity of each color to make your
desired color.
• Auto Run - Choose from 16 Color Change shows, 16 Color Fade
shows, or a combo Color Change & Fade show.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
Sound Active Mode:
In this mode the unit will react to sound, and chase through the differ-
ent colors.
1. Plug the fixture in and press the MODE button until “SoXX” is dis-
played. “XX” represents the sound active mode (1-16) currently dis-
played. Use the UP or DOWN buttons to scroll through the 16 sound
active programs.
2. When you have found your desired sound active program press the
SET UP button to adjust the sound sensitivity. When you press SET
UP, “SJ-X” should be displayed. Use the UP or DOWN buttons to
adjust the sensitivity. “SJ-1” is the least sensitive, “SJ-8” is the
most sensitive.
RGBWA+UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press
WiFly EXR HEX Par Operating Instructions
Operating Power:
There are two ways to supply power to this unit; battery power or AC
power.
• AC Power - To run the unit using AC power, plug the unit into a
power source, and put the Load Switch into the ON position. When
using AC power make sure the Battery Switch is in the OFF position.
• Battery Power - To run the unit using Battery power, put the
Battery switch and Load Switch into the ON position.
LED Display Lock:
The display will lock after 30 seconds. Press and hold the MODE
button for at least 10 seconds to unlock the display and access the
menu. When the display is unlocked a digital dot will blink at the bot-
tom of the right side of the display.
Battery Life:
This is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until “bXXX” is
displayed. “XXX” represents the remaining battery life. If “b----” is
displayed, it means either the battery is dead, your running the
unit on AC power, or your charging.
Energy Saving Mode
This will decrease the LED’s brightness gradually when the battery
life is less than 80%, this is will extend the battery life.
1. To activate energy saving mode, press the MODE button until
“bXXX” is displayed. “XXX” represents the current battery life.
2. Press the SET UP button so that “bSXX” is displayed. “XX” repre-
sents either “of” or “on” If “on” is displayed already then the fix
ture is already in energy saving mode. Use the UP or DOWN but-
tons to turn energy saving mode either “Off” or “On”.
LED Display On/Off:
To set the LED display to turn off after 60 seconds, press the MODE but-
ton until “don” is displayed, press the UP button to display “doff”. Now
the display will disappear after 60s. Press any button to turn the display
on again. Be advised though that the display will turn off automatically
after 10 seconds.
To set the display press the MODE button until “dXX” is displayed. Use
ADJ Products, LLC - www.adj.com - WiFly EXR HEX Par User Manual Page 10