ADJ Products, LLC - www.adj.com - WiFly Chameleon User Manual Page 16
WiFly Chameleon Operating Instructions
Operating Power:
There are two ways to supply power to this unit; battery power or AC
power.
• AC Power - To run the unit using AC power, plug the unit into a
power source, and put the Load Switch into the ON position. When
using AC power make sure the Battery Switch is in the OFF position.
• Battery Power - To run the unit using Battery power, press the bat-
tery button located on the bottom of the fixture across from power
input connection. Follow the instructions on page 15 to activate the
battery load.
Display Lock:
The display will lock after 30 seconds. Press and hold the MODE
button for at least 10 seconds to unlock the display and access the
menu. After 20 seconds of inactivtiy the display will switch back to
the battery life display
Energy Saving Mode
This will decrease the LED’s brightness gradually when the battery
life is less than 80%, this is will extend the battery life.
1. To activate energy saving mode, press the MODE button until
“Energy SAVE:XX” is displayed. “XX” represents either “ON” or
“OFF”.
2. Press the UP or DOWN button so that “ON” is displayed. If “ON”
is displayed already then the fixture is already in energy saving
mode.
LED Display On/Off:
To set the LED display light to turn off after 20 seconds, press the
MODE button until “OPTION” is displayed. Press the SET UP button
so that BLGT:XXX” is displayed. “XXX” represents either ON or OFF.
Press the UP or DOWN buttons so that OFF is displayed. Now the
display light will turn off after 30s. Press any button to turn the dis-
play on again.
ADJ Products, LLC - www.adj.com - WiFly Chameleon User Manual Page 19
program. Use the UP or DOWN button to adjust the speed
between “01” (slowest) and “16” (fastest). Once you have set your
desired running speed, you can press the SET UP button to enter
the fade adjustment mode.
3. Pressing the SET UP button will display “FADE:XX”. When this is
displayed you can adjust the fade speed of your desired program.
Use the UP or DOWN button to adjust the speed between “01”
(fastest) and “15” (slowest) or “00” (Off).
4. Press the SET UP button again and “STRO:XX” will be displayed.
This is strobe adjustment, you can adjust the strobe speed of your
desired program using the UP or DOWN buttons. You can adjust
the speed between “01” (fastest) and “15” (slowest) or “00” (Off).
• PROGRAMS 21 & 22 - If you have chosen either programs 21 or
22, after the strobe adjustment, press the SET UP button.
“B:XX” will be displayed. This is the base or background color,
use the UP and DOWN buttons to scroll through the different
color settings. Once you have chosen your base color, press the
SET UP button again so that “C:XX” is displayed. This is the
moving color, use the UP and DOWN buttons to scroll through the
different colors.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The WiFly
Chameleon has 6 DMX modes: 6 Channel mode, 7 Channel mode,
9 Channel mode, 11 Channel mode, 18 Channel mode, and a 20
Channel mode. See pages 10-15 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“DMX MODE: is displayed. Press the SET UP button so that
ADDR:XXX” is displayed. “XXX” represents the current displayed
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
WiFly Chameleon Operating Instructions