manualshive.com logo in svg

ADJ WiFly Chameleon, Инструкция пользователя, Страница: 15 / 18

Поделиться
Скачать
ADJ WiFly Chameleon Скачать руководство пользователя страница 15

ADJ Products, LLC  -  www.adj.com  - WiFly Chameleon User Manual Page 14

  WiFly Chameleon                                    18 Channel Mode

  Channel   Value  

                  Function

       

1               0 - 255               RED PIXEL 1 0% - 100%

       2               0 - 255           GREEN PIXEL 1 0% - 100%

       3               0 - 255             BLUE PIXEL 1 0% - 100%

       4               0 - 255            WHITE PIXEL 1 0% - 100%

       5               0 - 255           AMBER PIXEL 1 0% - 100%

       6               0 - 255               UV PIXEL 1 0% - 100%

       7               0 - 255               RED PIXEL 2 0% - 100%

       8               0 - 255           GREEN PIXEL 2 0% - 100%

       9               0  -255             BLUE PIXEL 2 0% - 100%

      10              0 - 255            WHITE PIXEL 2 0% - 100%

      11              0 - 255           AMBER PIXEL 2 0% - 100%

      12              0 - 255               UV PIXEL 2 0% - 100%

      13              0 - 255               RED PIXEL 3 0% - 100%

      14              0 - 255           GREEN PIXEL 3 0% - 100%

      15              0 - 255             BLUE PIXEL 3 0% - 100%

      16              0 - 255            WHITE PIXEL 3 0% - 100%

      17              0 - 255           AMBER PIXEL 3 0% - 100%

      18              0 - 255               UV PIXEL 3 0% - 100%

ADJ Products, LLC  -  www.adj.com  - WiFly Chameleon User Manual Page 21

  WiFly Chameleon                            Operating Instructions

6.   When “AMBE” is displayed you are in Amber balance mode.    

    Press the UP and DOWN buttons to adjust intensity. 

5.   When “UV” is displayed you are in UV balance mode.    

 

    Press the UP and DOWN buttons to adjust intensity. 

8.   Press the SET UP button for 3 seconds to save your settings.

DMX State:

This mode can be used as a precaution mode, that in case the DMX 

signal is lost, the operating mode chosen in the setup is the running 

mode the fixture will go into when the DMX signal is lost. You can also 

set this as the operating mode you would like the unit to return to 

when power is applied. 

1.   Plug the fixture in and press the MODE button until “DMX MODE  

  

ADDR:XXX” is displayed.

2.   Press the SET UP button until “DMX MODE NO” is displayed. The  

    current DMX state will be displayed.

  •  “BLACK” (Blackout) - If the DMX signal is lost or interrupted, 

      the unit will automatically go into stand by mode.

  •  “HOLD” (Last State) - If the DMX signal is lost or interrupted,         

     the fixture will stay in the last DMX set up.    

  •  “AUTO” (Auto Run) - If the DMX signal is lost or interrupted, 

      the unit will automatically go into Auto Run mode.

3.   Press the UP or DOWN buttons to scroll through and select    

  your desired DMX state.

Activate IR Sensor:

This  function  is  used  to  activate  and  deactivate  the  infared  sen-

sor. When this function is activated you can control the fixture using 

the  ADJ  LED  RC4  (sold  separately),  UC  IR  (sold  separately),  and 

Airstream IR app. Please see pages 25-28 for remote  controls and 

functions. You must aim the remote at the IR sensor and be no more 

the 30 feet away.

1.   Plug the fixture in and press the MODE button until “OPTION” is  

   displayed.

2.   Press the SET UP button until “IR: XX” is displayed. “XX” repre- 

    sents either “ON” or “OFF”.

3.   Use the UP or DOWN buttons to either activate the remote func- 

    tion (On) or deactivate it (Off). 

Содержание WiFly Chameleon



















Отзывы:

Нет отзывов