ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 6
Flash Kling Batten Connections
When connecting you must use a CA
T 5 Straight Network cable.
When connecting you must use a CA
T 5 Straight Network cable.
In
st
all
ati
on
m
et
hod
1
:
N
ot
e:
D
o
no
t d
ai
sy
-c
ha
in
m
or
e t
ha
n
50p
cs
LE
D
p
an
el
s f
ro
m
th
e
co
m
pu
te
r,a
nd
u
se
a
n
Et
he
rn
et
Sw
itc
h i
f m
or
e t
ha
n
50p
cs
LE
D
li
gh
ts
a
re
b
ei
ng
c
on
tro
lle
d.
N
ot
e:
1.
Th
e
Et
he
rn
et
Sw
itc
h
m
us
t b
e
G
ig
ab
it
Sw
itc
h.
2.
D
o
no
t d
ai
sy
-c
ha
in
m
or
e t
ha
n
50p
cs
LE
D
p
an
el
s f
ro
m
a
si
ng
le
n
et
w
or
k
po
rt
of
th
e
Et
he
rn
et
Sw
itc
h.
3.
M
ax
im
um
2
ou
tpu
t n
et
w
or
k
po
rts
o
f t
he
E
th
er
ne
t S
w
itc
h
ca
n
be
u
se
d.
So
th
e
sy
st
em
ca
n
con
tro
l 100p
cs
p
an
el
s m
ax
im
um
.
In
st
all
ati
on
m
et
hod
2
:
ADJ Products, LLC - www.adj.com - Flash Kling Batten Instruction Manual Page 5
Flash Kling Batten Operation
Control Using Kling-net or Art-Net:
1. Install one of the recommended operating softwares onto your
computer. Recommended softwares; Arkaos Media Master
Express, Media Master Pro, or LED Master (Sold Separately).
2. Connect the panels via CAT 5 Straight Network cable. When
creating your own custom cable, use RJ45 Straight Network
cable.
3. Map the fixtures using KlingNetMapper or Art-Net Mapper.
4. Control the fixtures using ArKaos or Art-Net software. Please refer
to the media playback software user manual for further instruc-
tions.
Note: ArKaos Kling-Net requires a gigabit (1000 mbps) Ethernet card
and network router for a smoother operation.
Connecting to Power and Data:
When connecting to power, the LED indicator on the bottom of the
unit should glow a solid red if the unit is receiving power.
When the unit is receiving a data signal, the LED indicator will flash
yellow.
Note: The LED indicator may only flash when pressing the mouse and
moving the indicator arrow around in the grid.
Flash Kling Batten Daisy-Chaining Units
Do not daisy-chain more than 50 Panels when connecting directly to
a computer. To daisy-chain more than 50 Panels you must use a Eth-
ernet Switch. When using a Ethernet Switch, do not daisy-chain more
than 50 Panels from a single network port of the Ethernet Switch. A
maximum 2 output network ports of the Ethernet Switch can be used.
So the system can control 100 Panels maximum, no more. See the
directions under the connection diagrams on page 6.
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 12 fixtures maximum After the maximum fixtures
has been reached you will need to use a new power outlet. They
must be the same fixtures. DO NOT mix fixtures.
Flash Kling Batten Daisy-Chaining Units
