background image

Control Panel Layout and Buttons Configurations:

 

RANGE HOOD OPERATIONS

While the range hood is off and Auto Function is activated, the blower will turn on to its highest

 speed     

        

automatically when the internal temperature is 4 times above the external temperature.

 Then it will         

        

adjust the speed level (between speed levels F4 to F1) automatically according to the

 detected tempera-    

        

ture between the sensors (4 times to 1 time). The speed level can also be

 manually overwritten by   

        

press the

Increase

or

Decrease

button and Auto Function will reactivate

 after 2 minutes. The blower can   

        

ONLY be turned off MANUALLY or activate the delay off timer

 finction.

While the range hood is off, press and hold

Auto Function

button to enter the temperature setting

 

mode.

        

Press

Increase

or

Decrease

button to adjust the comparison temperature value between

 the internal   

        

and external heat sensors from 8°F to 20°F. The temperature setting mode will exit

 automatically after 

       

5 seconds of inactivity.

Press

Auto Function

button to Turn On/Off the Auto Mode. The Auto Function Icon will appear in

 the

        

LCD Panel when Auto Mode is On.

In addition to the remote-control feature, this range hood is also equipped with a heat sensor that will selfcali-

brate in 5 seconds when the range hood is first electrically activated and beeps when selfcalibration is

 

done.

To conserve energy, the LCD panel will turn off automatically after 5 seconds of inactivity.

Adjusting Heat Sensitive Auto Speed (HSAS) Function:

Activating Normal Blower Function:

While the range hood is off, press

Increase

or

Decrease

button to start the blower. Press

Increase

 button

to increase blower speed (F1 to F4) as indicated in LCD panel. The

Increase

button cycles

 blower settings

from off (00), quiet speed (F1), low speed (F2), medium speed (F3) to high speed

 (F4).

While the range hood is on and the blower is running, press

Decrease

button to decrease blower

 

speed

        

(F4 to F1) as indicated in LCD panel. The

Decrease

button cycle blower settings from highspeed (F4),

        

to medium speed (F3), low speed (F2), quiet speed (F1) to off (00).

Activating Light Function:

Press Light button once to turn on the lights, and once again to turn off the lights.

CAUTION: DO NOT touch the lights until switched OFF and cooled.

Activating Power-Off Delay Function:

While the range hood is on and the blower is running, press Power-Off

 Delay button to activate delay    

        

off timer and “Power-Off Delay” icon will appear in LCD panel

 .Adjust to desired period of delay off timer   

        

by pressing Increase or Decrease button (minimum 1 minute to maximum 15minutes.

 Timer begins to

        

countdown immediately, when it reaches 0, the blower will shut off.

Adjusting Clock Function:

14

While the range hood is off, press Power-off Delay button once to enter the clock setting mode,

 press 

Increase or Decrease button to set the Hour. Press the Power-off Delay button again to set

 the Min.

Press the Power-off Delay button again to exit the clock setting mode.

Содержание AP238-PS83-36





















Отзывы: