ADEMCO 4286 - Ademco Phone Module Скачать руководство пользователя страница 21

Страница: 21 / 36

System Status Reports (cont’d)

Annunciations when the system is in the disarmed state are:

“DISARMED, READY TO ARM" or “DISARMED, NOT READY

TO ARM"*.

If the message

“DISARMED, NOT READY TO ARM"

is heard, and

the “Zone Faults” report is not annunciated later (see Zone Faults
below), simply press the

✴

key to hear the particular zones that are

faulted.

Remote Access

If Remote Access has been turned off, the words "CALL-IN TO
SYSTEM OFF" will be annunciated. If Remote Access is on, no
announcement will be made.

Chime Mode

If the security system is in the

CHIME

mode during the status

reporting session and a door or window is opened, a 2-note chime
sound will be heard over the phone. **

** In some systems, chime sounds will not be heard when the system
has been accessed from an outside phone.

Zone Faults

If there is a zone fault (example, a door or window open), the word
"FAULT" will be annunciated, followed by a zone descriptor*** (for
example, “UPSTAIRS

BEDROOM”) and a 2-digit zone number

(zones below 10 will be annunciated with a leading zero). If zone
faults are not annunciated in your system, press

✴

key to hear

zones that are faulted.

Note: Silent alarms will be annunciated as faults.

*** If programmed by your installer.

Содержание 4286 - Ademco Phone Module





































Результаты поиска

Содержание 4286 - Ademco Phone Module

Отзывы:

Похожие инструкции для 4286 - Ademco Phone Module

Бренды по названию

Популярные бренды

ADEMCO 4286 - Ademco Phone Module, Руководство пользователя

Результаты поиска

Содержание 4286 - Ademco Phone Module

Отзывы:

Похожие инструкции для 4286 - Ademco Phone Module

Бренды по названию

Популярные бренды