4. Weighing function (weight measurement only)
1. Switch on the scale by using the tap-on-function. For this tap with your foot
shortly on the centre of the scale. A short peep tone will sound and the display
indicates the signal
„
888
“
and a few seconds later 0.0 kg. Now the scale is ready
to use.
2. Step on the centre of the scale. Remain stationary on the weighing platform and
do not you hold tight. After a few seconds your weight will be indicated.
3. After weighing step off the scale. The scale will switch off automatically after a
short peep tone.
5. Programming / Enter of personal data
Before first-time use your personal data like gender (female or male), body height, age
and fitness level (A1 = no sport, A2 = occasional sport, A3 = regular sport, A4 = daily
sport, A5 = athlete) must be programmed and saved under selected locations 1
–
12
(up to 12 persons). The enter keys are located below the display. To enter your
personal data please utilise the buttons:
(on button),
—
(minus button),
+
(plus button), (save button) and follow the
particular points:
1. Press the button
and the display indicates a
flashing
„
01
“
. To select your personal location
(1
–
12) press the button (
+
) or (
—
). After you
’
ve
selected the location press the button to save
the reading.
2. After you
’
ve selected your personal location
(e.g. personal location 03) the symbol for gender
starts to flash. To select the requested gender
( for female or for male), press the button
(
+
) or (
—
). After the selection for your gender
press the button to save the reading.
3. After you
’
ve selected your gender (e.g. female)
the symbol for body height starts to flash (default
170 cm). To enter your height press the button
(
+
) or (
—
). After the selection for your height
press the button to save the reading.
4. After you
’
ve selected your body height the symbol
for age starts to flash (default 30 AGE). To enter
your age press the button (
+
) or (
—
). After the
selection for your age press the button to save
the reading.
5. After you
’
ve selected your age the symbol for
fitness level starts to flash (default A 1). To enter
your fitness level (A 1
–
A 5) press the button (
+
)
or (
—
). After the selection of your fitness level
press the button to save the reading.
After completion of the input you will hear a short peep tone and the scale automatically
powers off. To enter personal data of further persons please repeat the steps listed
below.
6. Body Analysis
An analysis is only possible in bare feet. Your personal data must be entered first
(please see page 4 - 5).
1. Switch on the scale by using the tap-on-function. For this tap with your foot a few
seconds on the centre of the scale. The display pass through from 01 to 12 and back
to 01. Take off your foot from the scale when the display indicates the selected
location for your personal data.
2. At the first time measurement, the display indicates the signal
„
888
“
and a few
seconds later
„
0.0
”
kg. When you once used the scale the display indicates
„
888
“
not
anymore but the readings of your last measurement. This function allows you to
follow the changes between your measurements.
3. As soon as
“
0.0
”
kg appears on the display the scale is prepared for the
measurement.
4. Carefully step on the scale in bare feet and remain stationary while the measurement
is now taking place.
5. After a short peep tone, your weight will be indicated. Shortly after, while the analysis
is taking place, the signal
„
o
“
starts to move. After completion of the measurement,
the display indicates as follows:
1. Your weight and your body fat % and as bar graph an evaluation: underweight,
normal weight, slightly overweight, overweight
2. Your ideal weight in kg and your body water %
3. Your bone mass in kg, your muscle mass % and your daily calories requirement
in Kcal.
Your measured values will be shown in changes successively 3 times.
03
A 1
170
CM
30
AGE
01
03
A 1
170
CM
30
AGE
03
A 1
170
CM
30
AGE
03
A 1
170
CM
30
AGE
4
5
