background image

113362 - 25

www.adclaundry.com

23

Manual Reset

Burner Hi-Limit Instructions _________

Phase 7

This dryer was manufactured with a manual reset burner
hi-limit thermostat, which is monitored by the Phase 7
computer.  If the burner hi-limit is open prior to the start of
the drying cycle, the dryer will start momentarily and then
shut down, the Phase 7 computer will display “BURNER HIGH
LIMIT FAULT” with an audio indication.

If the burner hi-limit opens during a drying cycle, the Phase 7
computer will also display the same error code described
above, along with an audio indication.  If the drum temperature
is above 100° F (38° C), the dryer will continue to run with no
heat for 3 minutes or until the drum temperature has dropped
below 100° F (38° C).  The clear/stop button on the Phase 7
keypad must be pressed to clear the error condition.  The
open burner hi-limit must be reset “manually” prior to the start
of the next cycle.

Mechanical Timer

This dryer was manufactured with a manual reset burner
hi-limit thermostat.  If the burner hi-limit is open prior to the
start of the drying cycle, or during the cycle, the dryer will not
recognize the open state of the burner hi-limit and will start
or continue through the drying cycle with no heat.  Manual
reset hi-limit must be reset manually.

This hi-temperature condition may be caused due to a
restricted exhaust, poor airflow, or improper burner operation.

The location of the burner hi-limit is on the front right side of
the burner box.

!

 WARNING

Discontinue power to dryer before attempting to reset
hi-limit.

  NOTES _____________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

____________________________________________________________

Содержание ML-96

























Отзывы: