manualshive.com logo in svg

ADC ADView 2 9005BPSTO, Руководство пользователя, Страница: 8 / 51

Поделиться
Скачать
ADC ADView 2 9005BPSTO Скачать руководство пользователя страница 8

     ADView 2 User Manual | 8 

93-9005-00

 rev 4

 

September 1, 2016

WARNING:

 Pulse rate measurement is based on the optical detection of a peripheral flow pulse and therefore may 

not detect certain arrhythmias. The pulse oximeter should not be used as a replacement or substitute for ECG-based 
arrhythmia analysis. 

WARNING:

 Do not use the device or any of its accessories during magnetic resonance imaging (MRI) scanning. 

Induced current could potentially cause burns. 

WARNING: 

Tissue damage can be caused by incorrect application or use of an SpO

2

 sensor, for example by wrapping 

the sensor too tightly. Inspect the sensor site as directed in the sensor Directions for Use to ensure skin integrity and 
correct positioning and adhesion of the sensor. 

WARNING: 

Do not use high frequency surgical equipment with the ADView 2 as this may cause loss of stored data 

WARNING:

 No modification of this equipment is allowed. 

WARNING

: 

Federal (U.S.) law restricts this device to sale by or on the order of a physician.

 

CAUTION

: A compressed or kinked connection hose may cause continuous cuff pressure resulting in blood flow 

interference and potentially harmful injury to the patient.

 

CAUTION:

 Check calibration of this device annually. 

CAUTION

: Calibration should be done by a biomedical technician or other authorized personnel. 

CAUTION: 

Never knowingly use a defective device. 

CAUTION: 

Immediately replace parts that are broken, worn, missing, incomplete, damaged or contaminated. 

CAUTION: 

Contact the nearest ADC-approved service center should repair or replacement become necessary. A list 

of approved service centers appears in the guide or on our website at 

www.adctoday.com.

 

CAUTION:

 The reliability of the device depends upon conformance with the operation and service instructions, as 

detailed in this manual. 

CAUTION

: Only replace battery with same type and model number. 

CAUTION:

 To avoid the risk of electrical shock, this equipment must be only connected to supply mains with 

protective earth. 

CAUTION

: Do not connect the device to equipment that does not meet EN60601-1. When the device is attached to a 

patient, the device’s communication ports must only be connected to equipment that meets EN60601-1 standard. 

CAUTION:

 Use only ADC-branded cuffs approved for use on the ADView 2 device. 

CAUTION:

 Use only Masimo oximetry sensors for SpO

2

 measurements with the Masimo SpO

2

 module. Other oxygen 

transducers (sensors) may cause improper performance. 

CAUTION:

 Do not use damaged SpO

2 

or temperature sensors. Do not use an SpO

2

 sensor with exposed optical 

components. 

CAUTION:

 Do not immerse the SpO

2

 or temperature sensors in water, solvents, or cleaning solutions (the sensors and 

connectors are not waterproof). Do not sterilize by irradiation, steam, or ethylene oxide. See the cleaning instructions 
in the Sensor Directions for Use. 

CAUTION:

 Do not use damaged patient cables. Do not immerse the patient cables in water, solvents, or cleaning 

solutions (the patient cable connectors are not waterproof). Do not sterilize by irradiation, steam, or ethylene oxide. 
See the cleaning instructions in the Patient Cable Directions for Use. 

CAUTION:

 Do not position the device so that it is difficult to access and remove the power cord from the electrical 

supply. The AC power cord is the means of disconnection to the supply mains. 

Содержание ADView 2 9005BPSTO




















































Отзывы:

Нет отзывов