manualshive.com logo in svg

ADC ADView 2 9005BPSTO, Руководство пользователя, Страница: 36 / 51

Поделиться
Скачать
ADC ADView 2 9005BPSTO Скачать руководство пользователя страница 36

     ADView 2 User Manual | 36 

93-9005-00

 rev 4

 

September 1, 2016

and Check Mark Icon

 will start flashing. Press the Selection Knob to send the data to the EMR. If the 

measurements are delivered to the EMR successfully, you will see the EMR Message Icon

 and the Check Mark 

Icon

flash four times. 

If the EMR has a problem receiving the measurements, the EMR Message icon

 and X icon

 will flash eight 

times and you will hear 4 short beeps. You will see a message indicating the nature of the problem, such as: 

“Rejected” or “Rejected for an error.” This message occurs when the device is connected to the network but the EMR 
rejects the message. A corresponding message will appear in the Patient ID field during a three-second period when 

the Message Icon

 and X icon

 flash on and off. 

“No response (time out).” This message occurs when the device is connected to the network but the EMR is not 
responding. It also can occur if network connectivity is lost. If there is a network connection, the ADView 2 will 
continue to try to transmit the message every 10 seconds. A message in the Patient ID field will alert you that another 
attempt to send the message will be made in 10 seconds. If network connectivity is lost, you will see a corresponding 
message in the Patient ID field, and the device will continue trying to re-establish a connection and send the 
measurements at intervals set during EMR setup. If problems persist, you may wish to contact your facility’s 
information technology department. As a backup, the patient’s measurements are saved in the device memory when 
the memory button was pressed, and can be retrieved using the procedure detailed in the beginning of Section 9.  

Note: After the memory button is pressed, all values to be stored to memory will flash off and on twice, along with the 

check mark icon, memory icon and memory location identifier. After flashing, the display will revert to null values for 

the patient ID and all measurement data, and the check mark icon will flash off and on twice more. 

10. Taking Care of Your ADView 2

Cleaning 

CAUTION: 

The ADView 2

 

is not sterilizable. Do not immerse the monitor in any fluid or attempt to clean with 

any liquid detergents, cleaning agents, or solvents. 

Dampen a soft cloth with mild medical grade disinfectant and wipe the device to remove surface dust and dirt. Dry 
surface thoroughly before use. 

SpO

2

 Sensors and Thermometers 

CAUTION: 

Never immerse sensors, clips or thermometers in fluids. Do not pour or spray any liquids onto the 

sensor or thermometers. Caustic or abrasive cleaners will cause permanent damage. Do not open the case of the 
Sp02 sensor finger clip sensor more than 45° or the case will be damaged. 

Clean the Sp02 sensor and thermometers with a soft cloth dampened with a mild medical grade disinfectant or 
isopropyl alcohol. Remove all tape residues. Allow the sensor and thermometer to dry thoroughly before reusing. 

Содержание ADView 2 9005BPSTO




















































Отзывы:

Нет отзывов