ADB L-862S Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 30

background image

© ADB Airfield Solutions All Rights Reserved

17

2.5 Troubleshooting

Refer to Table 8. This section contains troubleshooting information. This information covers
only the most common problems that you may encounter. If you cannot solve the problem
with the information given here, contact your local ADB Airfield Solutions representative for
help.

Table 8:

L-862S Light Fixture Troubleshooting

WARNING

Allow only qualified personnel to perform the following tasks. Observe and follow the safety
instructions in this document and all other related documentation.
De-energize the circuit and lock out the circuit or regulator so that the circuit cannot be energized
by remote means before attempting to service the fixture.

Problem

Possible Cause

Corrective Action

Lamps not turning
on

Defective lamp

Replace lamp. Refer to “Lamp Replacement” on
page 18.

Loose wire connection(s)

Tighten wire connection(s).

Isolation transformer bad

Replace transformer.

Deteriorated wire insulation Replace wires.

Moisture present in fixture

Open up and dry. Inspect lens for cracks. Replace
lamp and any damaged parts. Refer to “Lamp
Replacement” on page 18 or

“Lens, Reflector, and

Gasket Replacement” on page 18.

«
...
21
22
23
24
25
...
»

Содержание L-862S































Отзывы:

Нет отзывов

Похожие инструкции для L-862S

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: Fisher Scientific Страницы: 42

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Sabre Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jacto Страницы: 64

Бренд: Launch Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды