manualshive.com logo in svg

ADB Stagelight EURODIM Twin Tech, Руководство по установке

Поделиться
Скачать
ADB Stagelight EURODIM Twin Tech Скачать руководство пользователя страница 25

EURODIM TWIN TECH 

 

 

User Manual - page 23 
Issue 2.1 

www.adbstagelight.com

 

 

 

6  SEQUENTIAL DIAGNOSTICS (Optional) 

In case the client has ordered the option: 
One  Sequential  Diagnostics  kit  must  be  installed  for  each  dimmer  cabinet  in  the 
installation. 

 

The sequential diagnostics function is similar in function to the diagnostics already used in 
the EURODIM 3. The dimmer channels are examined one after the other (sequential) and 
the value is reported either to the local Human Interface or a remote program running the 
TTD Management Software. 

 

The communication to a single remote reporting pc is done via RDM protocol based on an 
Ethernet  Network  to  a  Personal  Computer  with  the  Windows  Operating  System  running 
the  TTD  RDM  Management  Software.  The  Ethernet  information  is  generated  by  each 
EURODIM  Twin  Tech  controller  and  physically  available  for  each  individual  controller  on 
dedicated  RJ45  connectors  (Two  possible  per  cabinet  if  double  controller  options  are 
used). 

 

The TTD RDM Management Software and the necessary hardware are available as option 
for the EURODIM Twin Tech cabinet, which shall be ordered separately installation. 
 

Standard functions include 
 

•

  Presence of Mains and DMX signal 

•

  Processor (active) check 

•

  Over Temperature 

•

  Fan Failure (Information per FAN!) 

•

  DMX Control Levels 

•

  Local test of a dimmer (steady, flash or chaser) 

•

  Automatic self-test of control electronics. 

 

Error  messages  and  all  events/parameters  are  available  for  display  locally  on  the 
EURODIM  Twin  Tech  Human  Interface  Controller  and/or  remotely  on  the  TTD  RDM 
Dimmer Manager PC connected via an Ethernet Network. 
Scan  Load  and  the  related  functions  are  pre-show

1

  test  routines  providing  additional 

information on the status of each dimmer, i.e. 
 

•

  Value of the dimmer load (kW) 

•

  Deviation from reference load 

•

  No load, overload warnings 

•

  Short-Circuit 

 

The necessary hardware to perform Sequential Diagnostic measurements is an option and 
which shall be installed at the client’s site. 

 
 

1 

Sequential Diagnostics cannot be used during a show, since control is disabled and the dimmers system 

runs through a test routine. 

Содержание EURODIM Twin Tech








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды