manualshive.com logo in svg

ADB Stagelight EURODIM Twin Tech, Руководство по установке

Поделиться
Скачать
ADB Stagelight EURODIM Twin Tech Скачать руководство пользователя страница 11

EURODIM TWIN TECH 

 

 

User Manual - page 9 
Issue 2.1 

www.adbstagelight.com

 

 

 

CAUTION! 

 

 

Installation  is  entirely  at  your  own  risk.  Read  this  installation  manual  from  cover  to 
cover before attempting installation. Do not attempt installation unless you are suitably 
qualified.  Installation  errors  may  endanger  operators  and  cause  system  damage  and 
failure.  If  you  do  not  understand  a  point  in  this  manual,  don’t  guess.  Contact  ADB  or 
one of our authorized distribution partners for advice. 
We recommend ordering commissioning through ADB or one of our authorized 
partners prior energizing the system. Not following this recommendation may result in 
equipment damage that may not be covered by your warranty! 
 

The equipment shall be installed and serviced by skilled and trained personnel 

exclusively. 

 

 

1.1  Safety 

 

The  Eurodim  twintech  is  professional  fully  digital  dimmers  built  in  accordance  with 
European safety standards EN 62368. 
It  is  a  Class  I  equipment  designed  and  manufactured  to  EN  62368  and  requires 
imperatively a safety earth connection in compliance with local regulations.  
 
To prevent any risk of electric shock, do not remove any cover or part of the enclosure. 
Access to internal parts is not required for normal operation. 

Refer servicing to skilled 

and  trained  service  personnel  exclusively

.  Disconnect  from  the  power  supply  prior  to 

opening for inspection or service. 
 

WARNING!  LETHAL VOLTAGES ARE PRESENT INSIDE 

 
Connection to an inappropriate power source may irreversibly damage the dimmer unit, it 
is the user’s responsibility to use it for its intended purpose and to check the equipment 
connected to it. 
 
The  Eurodim  Twintech  is  professional  equipment  developed  with  the  simplicity  of  use  in 
mind. 
However, to obtain full benefits of the safety measures, the equipment shall be installed 
and serviced by skilled and trained personnel exclusively. 
 
 
 

This equipment is not suitable for use in locations where children are likely to be present 

 

 

Содержание EURODIM Twin Tech








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды