ADB Safegate AXON FAA L-852A Скачать руководство пользователя страница 45

Страница: 45 / 98

Note

Refer to the

Opening a Light Fixture — disconnecting the Bottom Pan from the Top Cover

section.

2. Remove the Light Engine(s) (4 pieces M4 screws per light engine assembly.

Figure 15: Light engine removal

Make sure to dispose the old screws and the old top cover and use the new material.

3. Replace the old top cover with new top cover assembly.
4. Mount the light engine(s) into the new top cover assembly.
5. Use new screws to attach the light engine in star pattern at 31 inch-pound (3.5 Nm).

6. Retorque the screws in star pattern at 31 inch-pound (3.5 Nm).
7. Close the light.

Note

Refer to the

Closing a Light Fixture — connecting the Bottom Pan to the Top Cover

section.

5.3.7 Replacing the Bottom Cover Assembly

Tools to be used:

•

Screwdriver T25 bit

•

Flat-head screwdriver

1. Open the light.

Note

Refer to the

Opening a Light Fixture — disconnecting the Bottom Pan from the Top Cover

section.

Make sure you dispose the old bottom cover assembly and use the new assembly.

2. Close the light.

Note

Refer to the

Closing a Light Fixture — connecting the Bottom Pan to the Top Cover

section.

UM-5056, Rev. 1.0.17, 2022/12/08

Содержание AXON FAA L-852A

























































































Результаты поиска

Содержание AXON FAA L-852A

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate AXON FAA L-852A, Руководство пользователя

Результаты поиска

Содержание AXON FAA L-852A

Отзывы:

Бренды по названию

Популярные бренды