PRODUCT MUST BE INSTALLED
ACCORDING TO ALL APPLICABLE
BUILDING AND LIFE SAFETY CODES
120V AC
LINE
VOLTAGE
4605 / 4606 -24V AC
40 VA TRANSFORMER
4603
2-AMP
RECTIFIER
RED -
RED -
BLACK (-)
WHITE (+)
2190
DEADBOLT / DEADLATCH
2190 WIRING DIAGRAM
INTERMITTENT / CONTINUOUS DUTY 12 / 24V DC
ELECTRIFIED TRIM SOLENOID SPECIFICATION
SOLENOID AVAILABLE VOLTAGES
12V DC CONTINUOUS DUTY,
24V DC CONTINUOUS DUTY.
INTERIOR TRIM
EXTERIOR TRIM
BOTTOM CAP
COVER
TOP CAP
SET SCREW
#10-24 x 1/4"
(3/32" ALLEN WRENCH)
FILLISTER SCREW
#6-32 x3/8" (2) EA.
FLAT HD SCREW
#6-32 x 3" (6) EA.
DRIVE
SPINDLE
FLAT HD SCREW
#4-40 x1/4" (2) EA
DRIVE
SPINDLE
SHAFT
VOLTAGE
ADAPTOR CABLE
ELECTRIFIED
TRIM SOLENOID
WASHER
HUB
LOCK SCREW
26-0933
(1/8" ALLEN
WRENCH)
HANDLE
SHAFT DETENT
INSTALLING HANDLE (INTERIOR / EXTERIOR)
- INSERT WASHER THEN INSERT HUB OVER SHAFT.
ON HANDLES 2190-01, 2190-02, 2190-03, THE HUB IS FACTORY
INSTALLED. REMOVE LOCK SCREW WITH 1/8" ALLEN WRENCH
AND PROCEED TO NEXT STEP.
- INSTALL HANDLE OVER THE HUB WITH THE HOLE ALIGNED
WITH THE HOLE ON THE HUB.
NOTE: THE SHAFT DETENT SHOULD BE ALIGNED
WITH THE LOCKING SCREW.
- MOVE THE HANDLE IN UNTIL IT IS
AGAINST THE TRIM COVER.
- FASTEN THE LOCK SCREW 26-0933
TO SECURE THE HANDLE WITH 1/8"
ALLEN WRENCH.
11
3/32"
ALLEN
WRENCH
FIG. 2
PUSH
UP
HOLD BACK
BUTTON
- EXTEND THE WIRE RUN FROM THE POWER SORCE
AND THROUGH THE ACCESS HOLE ON THE EXTERIOR SIDE
OF THE STILE.
- ATTACH VOLTAGE ADAPTOR CABLE TO 2190 AS SHOWN.
LATCH BOLT
DEADBOLT
HOLD BACK
BUTTON
KEY OR
THUMB TURN
HOLD BACK
BUTTON
PUSH
DOWN
LATCH HOLD BACK FEATURE
- IN THE LOCK POSITION, INSERT KEY,
TURN KEY 180° TO RETRACT THE DEADBOLT.
- TURN KEY 315° TO RETRACT THE LATCHBOLT.
- HOLD IN THIS POSITION AND PUSH DOWN
THE HOLD BACK BUTTON TO RETAIN LATCHBOLT.
- RETURN KEY TO NEUTRAL POSITION AND REMOVE KEY.
TO RELEASE HOLD BACK
- INSERT KEY, TURN KEY OR THUMB TURN
ABOUT 135° AND HOLD.
- PUSH UP THE HOLD BACK BUTTON TO RELEASE
THE LATCH BOLT.
- RETURN KEY TO THE NEUTRAL POSITION
AND REMOVE KEY.
TEST OPERATION
- EXTEND DEADBOLT WITH KEY OR THUMBTURN.
- PUSH DOWN ON INTERIOR LEVER.
THE DEADBOLT AND LATCH SHOULD FULLY RETRACT.
- IF LATCH ONLY RETRACTS - REFER TO STEP 4 FOR
INTER-CONNECTION CONFIGURATION.
- IF NEITHER RETRACT - REFER TO STEP 11 FOR
DRIVE SPINDLE INSTALLATION.
- PUSH DOWN ON EXTERIOR LEVER - THE LATCH ONLY
SHOULD RETRACT.
- INSERT DRIVE SPINDLE INTO EACH TRIM BODY
PRIOR TO MOUNTING.
- MOUNT THE EXTERIOR TRIM AND
INTERIOR TRIM BODY TO THE STILE
USING (6) #6-32 x 3" FLAT HEAD SCREWS.
- SLIDE THE COVER ONTO INTERIOR TRIM BODY
FROM THE TOP.
- INSERT SHAFT THRU THE HOLE ON THE
COVER AND THE OUTPUT ON TRIM BODY.
THE GROOVE ON THE SHAFT FACES
OPPOSITE THE LATCH BOLT.
TIGHTEN THE SET SCREW WITH A 3/32" ALLEN
WRENCH TO SECURE THE SHAFT AS SHOWN
IN
FIG. 2.
- INSTALL TOP CAP USING (2) #4-40 x1/4" FLAT
HEAD SCREWS .
- PUSH THE COVER UP FLUSH WITH THE
TOP CAP, INSTALL BOTTOM CAP USING
(2) #6-32 x 3/8" FILLISTER HEAD SCREWS.
10
INSTALLING INTERIOR & EXTERIOR TRIM TO STILE
Page of
3
3
INSTALLATION INSTRUCTIONS
Rev.
Appvd: BC
Date:
ECN: 11883
Date: 02/09/12
D
80-0180-410
02/03/12
Adams Rite Manufacturing Co.
260 Santa Fe Street,
Pomona, CA 91767
Phone: 909-632-2300
Fax: 909-632-2369
www.adamsrite.com
2190 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET
