B
A
TR
DOOR CL
*
"TR"
is trim ring length
"A"
is cylinder height (less
shoulder but including cam)
"B"
is one-half of door thickness
TOLERANCE: ±.060
TR* = A - B
CYLINDER
TRIM RING
DOOR STILE
LOCK CASE
CAM
- INSTALL CYLINDER AND SECURE WITH SET SCREWS.
- INSTALL FACE PLATE.
- INSERT LOCK ASSEMBLY INTO LOCK STILE THRU CUTOUT.
- INSTALL AND FASTEN TWO (2) FLAT HEAD SCREWS
#10-32 x 1-7/8" TO SECURE THE LOCK ASSEMBLY ON STILE.
INSTALLING LOCK TO THE BACK OF THE STILE
6
7
5.80
6.874
"A"
"B"
.750
.688
2.856
1.362
1.004
.626
1.587
1.737
3.200
.980
.476
3/16"
HEX KEY
MATCH MEASURED
DISTANCE
INSIDE
LOCK
STILE
WALL
FOR MOUNTING TAB INSTALLATIONS
-REMOVE TOP AND BOTTOM FLAT HEAD UNDERCUT
SCREW #8-32 x 1/4"AS SHOWN.THEN REMOVE YOKE.
(MOUNTING TABS NOT INCLUDED).
YOKE
FLAT HD UNDERCUT SCREW
#8-32 x 1/4"
FLAT HD
SCREW
#10-32 x 1-7/8"
2 EA.
CYLINDER
SET SCREWS
FACE
PLATE
CUTOUTS
FINISH
COVER
EXTERIOR
TRIM BODY
GROOVES
EXTERIOR TRIM LHR
CW SHOWN
INTERIOR TRIM LHR
CCW SHOWN
BACK VIEW
SHOULDER
SCREW
OUTPUT
DRIVE
2 15/32"
STRIKE PLATES ARE SHOWN
AT FRONT SIDE FOR CLARITY
CL OF
STRIKE
PLATE
CL OF CYLINDER
ADJUST
TUBE
SPACERS
EQUALLY
CYLINDER
SET SCREW
*SHIELD
ASSY.
FINISH
COVER
TOP CAP
BOTTOM
CAP
EXTERIOR
TRIM BODY
FLAT HD SCR
#4-40 x 1/4"
4 EA
FOR TRADITIONAL MOUNTING INSTALLATIONS
- MEASURE THE DEPTH FROM THE BACK OF THE LOCK STILE
TO THE INSIDE WALL OF THE LOCK STILE.
- MATCH THE DISTANCE FROM THE FACE OF MOUNTING
PLATE TO END OF BOTH TUBE SPACERS.
- USE 3/16" HEX KEY FOR FINE ADJUSTMENT.
5
4
ASSEMBLE EXTERIOR TRIM
8
9
- THE OUTPUT DRIVE FOR THE EXTERIOR TRIM IS SHIPPED FROM THE FACTORY IN A CLOCKWISE
ROTATION AND THE INTERIOR TRIM IS SHIPPED WITH A COUNTER-CLOCKWISE ROTATION.
TO CHANGE THE OUTPUT DRIVE ROTATION, FOLLOW THESE STEPS:
1. REMOVE THE SHOULDER SCREW WITH A 5/64" ALLEN WRENCH.
2. REINSTALL SHOULDER SCREW ON THE OPPOSITE SIDE.
REFER TO THE CHART BELOW FOR REHANDING THE TRIM AS NEEDED.
HANDING CONFIGURATION FOR 2190 TRIM
-SLIDE THE FINISH COVER ONTO BODY. THE COVER HAS CUTOUTS THAT FIT OVER
THE GROOVES ON THE BODY.
- INSTALL TOP CAP WITH (2) FLAT HEAD SCREWS (#4-40 x1/4") SUPPLIED.
- *FOR EXTERIOR TRIM WITH ELECTRIFIED OPTION. INSERT THE SHIELD ASSY
BETWEEN THE COVER AND THE EXTERIOR TRIM BODY BEFORE INSTALLING
THE BOTTOM CAP.
- INSTALL BOTTOM CAP WITH (2) FLAT HEAD SCREWS (#4-40 x1/4") SUPPLIED.
Page of
2
3
INSTALLATION INSTRUCTIONS
Rev.
Appvd: BC
Date:
ECN: 11883
Date: 02/09/12
D
80-0180-410
02/03/2012
Adams Rite Manufacturing Co.
260 Santa Fe Street,
Pomona, CA 91767
Phone: 909-632-2300
Fax: 909-632-2369
www.adamsrite.com
2190 INSTALLATION INSTRUCTIONS
W/ HEAVY DUTY ENTRANCE LEVER SET
