Adam Equipment NBL 12001e Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 52

background image

EN

© Adam Equipment Company 2015

19

3016612481Rev2.00-Jul15

10.3 WEIGHING

Press [

0/T



] to zero the balance if required. The “

0



“ symbol will be displayed.

Carefully place a mass on the pan and the weight will be displayed with the

symbol

on the left hand side of the display to indicate that a stable reading has been obtained.

If a container is to be used, place it on the balance and press [

0/T



] to tare the weight.

When the balance symbol

is on, the “

Net

” symbol will be displayed to indicate that the

balance is tared.

When the display shows zero, place the item to be weighed. Only the net weight will be
displayed.

When a tared weight has been stored, pressing [

0/T



] again will remove it.

At any time the [Unit] key may be pressed to select another unit. Use the [Up] or [Down]
keys to scroll through the units and select the desired unit by pressing [Setup], the display
will change to show the weight in the selected weighing unit. The available weighing units
can be enabled or disabled during setup of the balance (see section 13.1). Only weighing
units that have been enabled will be cycled through when [Unit] is pressed.

Weighing Units:
Note: Approved units have a restricted range of units available, depending on country of
approval.

You can select alternative weighing units to display the weight by pressing the [Unit] key.
Depending on model, the available weighing units may include:

Unit

Symbol Models

Conversion
Factor
1g =

Conversion
Factor
1 unit = grams

1 GRAMS

g

All

1

1.0

2 MILLIGRAMS

mg

not 0.01g &
0.1g units

1000

0.001

3 KILOGRAMS

kg

0.01g & 0.1g
units

0.001

1000

4 CARATS

ct

All

5

0.2000

5 PENNYWEIGHT

dwt

Some models

0.643014865

1.555174

6 GRAINS

GN

Some models

15.43236

0.0647989

7 TROY OUNCES

ozt

Some models

0.032150747

31.103476

8 OUNCES

oz

Some models

0.035273962

28.349523

9 POUNDS

lb

Some models

0.00220462

453.59237

10 POUNDS:OZs

lboz

Some models

0.035273962

1 lb = 16 oz

11 CUSTOM

Custom

Some models

As specified

As specified

It is possible to set the balance to display only grams. Grams will always be one of the
units enabled, by default.

If “Custom” unit is available and selected, the balance will prompt for entering a multiplier
by displaying “CF 1.2345”, where “1.2345” is the last stored value. Any value ranging from
0.100 to 10.000 may be entered, by which the weight in grams will be multiplied before

«
...
18
19
20
21
22
...
»

Содержание NBL 12001e





















































Отзывы:

Нет отзывов

Похожие инструкции для NBL 12001e

PROCISION TCH.C Series

Бренд: Transcat Страницы: 11

Бренд: FIRST AUSTRIA Страницы: 34

Бренд: Fast Weigh Страницы: 2

Бренд: Sartorius Страницы: 105

Simple Precision Weight Scale

Бренд: KAM Страницы: 12

Бренд: CDN Страницы: 2

Бренд: CDN Страницы: 2

Бренд: A&D Страницы: 82

Бренд: mensor Страницы: 8

Бренд: A&D Страницы: 31

Бренд: Silvercrest Страницы: 37

Бренд: Silvercrest Страницы: 64

Бренд: Silvercrest Страницы: 55

Бренд: Silvercrest Страницы: 66

Бренд: Silvercrest Страницы: 119

Бренд: Xavax Страницы: 14

Бренд: Salter Страницы: 2

Бренд: Salter Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды