background image

3.55  

Any discharge should be visible at the tundish. In addition, where discharges from 

safety devices may not be apparent, e.g. in dwellings occupied by people with impai-

red vision or mobility, consideration should be given to the installation of a suitable 

safety device to warn when discharge takes place, e.g. electronically operated.

Discharge pipe D2
3.56   The discharge pipe (D2) from the tundish should:

 

(a) have a vertical section of pipe at least 300mm long below the tundish before any 

elbows or bends in the pipework; and

 

(b) be installed with a continuous fall thereafter of at least 1 in 200.

3.57   The discharge pipe (D2) should be made of:

 

(a) metal; or

 

(b) other material that has been demonstrated to be capable of safely withstanding 

temperatures of the water discharged and is clearly and permanently marked to iden-

tify the product and performance standard (e.g. as specified in the relevant part of BS 

7291)

3.58   The discharge pipe (D2) should be at least one pipe size larger than the nominal outlet 

size of the safety device unless its total equivalent hydraulic resistance exceeds that 

of a straight pipe 9m long, i.e. for discharge pipes between 9m and 18m the equivalent 

resistance length should be at least two sizes larger than the nominal outlet size of the 

safety device; between 18 and 27m at least 3 sizes larger, and so on; bends must be 

taken into account in calculating the flow resistance. See figure, table and the worked 

example.

3.59   Where a single common discharge pipe serves more than one system, it should be at 

least one pipe size larger than the largest individual discharge pipe (D2) to be connec-

ted.

3.60   The discharge pipe should not be connected to a soil discharge stack unless it can 

be demonstrated that that the soil discharge stack is capable of safely withstanding 

temperatures of the water discharged, in which case, it should:

 

(a) contain a mechanical seal, not incorporating a water trap, which allows water into 

the branch pipe without allowing foul air from the drain to be ventilated through the 

tundish;

 

(b) be a separate branch pipe with no sanitary appliances connected to it;

 

(c) if plastic pipes are used as branch pipes carrying discharge from a safety device 

they should be either polybutalene (PB) to Class S of BS 7291-2:2006 or cross linked 

polyethylene (PE-X) to Class S of BS 7291-3:2006; and (d) be continuously marked 

with a warning that no sanitary appliances should be connected to the pipe.

Note:

1.  Plastic pipes should be joined and assembled with fittings appropriate to the circums-

tances in which they are used as set out in BS EN ISO 1043-1.

2.  Where pipes cannot be connected to the stack it may be possible to route a dedicated 

pipe alongside or in close proximity to the discharge stack.

Termination of discharge pipe
3.61   The discharge pipe (D2) from the tundish should terminate in a safe place where there 

is no risk to persons in the vicinity of the discharge.

3.62   Examples of acceptable discharge arrangements are:

 

(b) to a trapped gully with the end of the pipe below a fixed grating and above the 

water seal;

 

(c) downward discharges at low level; i.e. up to 100mm above external surfaces such 

as car parks, hard standings, grassed areas etc. are acceptable providing that a wire 

UK

Smart SL : A1007846 - 661Y3100 • C

Technical Characteristics

13

EN

Содержание SL320





























Отзывы: